Kenmore 9745 Use and Care Manual - Page 30

Setting Warmer

Drawer Controls

•

Warmer Drawer Humidity Controller (some models)

•

Removing & Replacing Warmer Drawer (some models)

Warmer

Drawer

Humidity

Controller

Feature

(some

models)

This feature may be used to control humidity

levels in the Warmer Drawer. The

control knob is located on the inner front panel of the Warmer

Drawer.

To help keep foods moist, move the handle to the right. This closes the vents and

helps keep the moisture

inside the Warmer Drawer.

For crisp foods, move the

handle to the left. This opens the vents and allows more of the moisture

to

escape.

For

Moist

Heat: Slide the humidity control knob in the direction

of (More)

(See Fig. 1). This will help keep the food in the Warmer Drawer from drying out.

Both heat and moisture will be applied to the Warmer

Drawer cavity.

For Dry Heat: Slide the humidity control knob in the direction

of (Less)

(See

Fig. 2). This allows more of the moist heat to escape and provides a dryer

environment

for the food in the Warmer Drawer.

Fig. 1

Fig.

2

Note: For some types of servings

you may want to store previously

prepared food in a "dry heat" environment.

For frequent

controller

adjustments,

slightly loosen humidity

controller

knob and slide to any desired position. To maintain a

desired setting, adjust controller

knob into position and tighten

knob.

Pull up with

finger

Left Glide

Remove shield

on right

glide.

Pull up

on

left lever

while

pushing down

on

right lever,

Push down

with

finger

Fig. 3

Glide

Fig. 4

NOTE: The Warmer Drawer will NOT

operate while in the Self:Clean and

,'Oven Lockout" modes

Warmer

(Warm

& Ready

TM)

Drawer

Indicator

Light

(some models)

The indicator light is located above the Warmer Drawer thermostat

control. It

turns on when the control

is set, and stays on until the control is turned OFF.

The warmer drawer is inoperable during the Self-Clean

cycle. The indicator light

will not come on during the Self-Clean

cycle.

Electrical

Shock Hazard can occur and result in

serious injury or death. Disconnect

appliance from electric power

before cleaning and servicing the warmer d rawer.

To Remove

and

Replace

Warmer

(Warm

& Ready

TM)

Drawer

(some

models)

To Remove

Warmer

Drawer:

1.

_

Turn powerOFF

before removing thewarmerdrawer.

2.

Open the drawer to the fully opened position.

3.

On the right glide you will find a shield attached with a hex-head screw (See

Fig. 3). Use a 1/4" socket and ratchet remove the shield.

4.

Locate glide lever on each side of drawer, pull up on the left glide lever and

push down on the right glide lever.

5.

Pull the drawer away from the range.

To

Replace

Warmer

Drawer:

1.

Replace shield on the right glide of the drawer body.

2.

Pull the bearing

glides

to the front

of the chassis

glide (See Fig. 4).

3.

Align the glide on each side of the drawer with the glide slots on the range.

4.

Push the drawer

into the range until levers "click" (approximately

2"). Pull

the drawer

open again to seat bearing glides into position. If you do not

hear the levers

"click"

or

the bearing

glides

do not feel seated

remove

the drawer

and repeat

steps

2=4. This will minimize

possible

damage to the bearing glides.

3O

Kenmore 9745 Use and Care Manual - Page 30

Warmer, Humidity, models, & Ready, Drawer, Indicator, To Remove, Replace

Page 30 highlights