Kenwood DDX4031BT User Manual - Page 69

Ddx4031bt/ddx4031btm Only, Ddx6031bt/ddx6031btm/ddx6031, Ddx6031m Only, Caution

Get Kenwood DDX4031BT PDF manuals and user guides View all Kenwood DDX4031BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

• If the power is not turned ON ("Miswiring DC Offset Error", "Warning DC Offset Error" is displayed), the speaker wire may have a shortcircuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. • If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, such as with battery wires, the battery may be drained. • If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. • If the fuse blows, first make sure the wires aren't touching to cause a short circuit, then replace the old fuse with one with the same rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. • When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Mount the unit so that the mounting angle is 30° or less. • Do not press hard on the panel surface when installing the unit to the vehicle. Otherwise scars, damage, or failure may result. • This unit has the cooling fan to decrease the internal temperature. Do not mount the unit in a place where the cooling fan of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction. Cooling fan DDX4031BT/DDX4031BTM only • Install the Bluetooth adaptor (KS-UBT1) besides the place enclosed by the metal. Bluetooth adaptor (KS-UBT1) DDX6031BT/DDX6031BTM/DDX6031/ DDX6031M only Before installation, remove the screws Use these screws when installing the unit (Same as Accessory 6). ¤ CAUTION Install this unit in the console of your vehicle. Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot. English 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
English
69
•
If the power is not turned ON (“Miswiring
DC Offset Error”, “Warning DC Offset Error” is
displayed), the speaker wire may have a short-
circuit or touched the chassis of the vehicle and
the protection function may have been activated.
Therefore, the speaker wire should be checked.
•
If your car’s ignition does not have an ACC
position, connect the ignition wires to a power
source that can be turned on and off with the
ignition key. If you connect the ignition wire to a
power source with a constant voltage supply, such
as with battery wires, the battery may be drained.
•
If the console has a lid, make sure to install the
unit so that the faceplate will not hit the lid when
closing and opening.
•
If the fuse blows, first make sure the wires aren’t
touching to cause a short circuit, then replace the
old fuse with one with the same rating.
•
Insulate unconnected wires with vinyl tape or
other similar material. To prevent a short circuit,
do not remove the caps on the ends of the
unconnected wires or the terminals.
•
Connect the speaker wires correctly to the
terminals to which they correspond. The unit may
be damaged or fail to work if you share the
-
wires
or ground them to any metal part in the car.
•
When only two speakers are being connected
to the system, connect the connectors either to
both the front output terminals or to both the rear
output terminals (do not mix front and rear). For
example, if you connect the
+
connector of the left
speaker to a front output terminal, do not connect
the
-
connector to a rear output terminal.
•
After the unit is installed, check whether the
brake lamps, blinkers, wipers, etc. on the car are
working properly.
•
Mount the unit so that the mounting angle is 30°
or less.
•
Do not press hard on the panel surface when
installing the unit to the vehicle. Otherwise scars,
damage, or failure may result.
•
This unit has the cooling fan to decrease the
internal temperature. Do not mount the unit in a
place where the cooling fan of the unit are blocked.
Blocking these openings will inhibit the cooling of
the internal temperature and result in malfunction.
Cooling fan
DDX4031BT/DDX4031BTM only
•
Install the Bluetooth adaptor (KS-UBT1) besides
the place enclosed by the metal.
Bluetooth adaptor (KS-UBT1)
DDX6031BT/DDX6031BTM/DDX6031/
DDX6031M only
Before installation, remove the screws
Use these screws when installing the unit
(Same as
Accessory
6
).
¤
CAUTION
Install this unit in the console of your
vehicle.
Do not touch the metal part of this unit
during and shortly after the use of the
unit. Metal part such as the heat sink and
enclosure become hot.