Kenwood KMR-M332BT Instruction Manual - Page 34

Part list for installation, Basic procedure, Installing the unit in-dash mounting

Get Kenwood KMR-M332BT PDF manuals and user guides View all Kenwood KMR-M332BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Installation/Connection Part list for installation (A) Faceplate (×1) (B) Trim plate (×1) Installing the unit (in-dash mounting) 1 (C) Mounting sleeve (×1) (D) Wiring harness (×1) (E) Extraction key (×2) (F) Screws* M5 × 7 mm (×4) M5 × 6 mm (×4) M4 × 8 mm (×1) * Supplied for / . Basic procedure 1 Remove the key from the ignition switch, then disconnect the terminal of the car battery. 2 Connect the wires properly. See "Wiring connection" on page 30. 3 Install the unit to your car. See the following "Installing the unit (in-dash mounting)". 4 Connect the terminal of the car battery. 5 Press BSRC to turn on the power. 6 Detach the faceplate and reset the unit within 5 seconds. (Page 4) 2 Hook on the top side Orientate the trim plate as illustrated before fitting. Do the required wiring. (Page 30) Dashboard of your car Bend the appropriate tabs to hold the sleeve firmly in place. 28 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
28
ENGLISH
Installation/Connection
Part list for installation
(A)
Faceplate (×1)
(B)
Trim plate (×1)
(C)
Mounting sleeve (×1)
(D)
Wiring harness (×1)
(E)
Extraction key (×2)
(F)
Screws*
M5 × 7 mm (×4)
M5 × 6 mm (×4)
M4 × 8 mm (×1)
* Supplied for
/
.
Basic procedure
1
Remove the key from the ignition switch, then disconnect the
terminal of the car battery.
2
Connect the wires properly.
See “Wiring connection” on page 30.
3
Install the unit to your car.
See the following “Installing the unit (in-dash mounting)”.
4
Connect the
terminal of the car battery.
5
Press
B
SRC to turn on the power.
6
Detach the faceplate and reset the unit within 5 seconds. (Page 4)
Installing the unit (in-dash mounting)
1
2
Do the required wiring.
(Page 30)
Bend the appropriate tabs to hold the sleeve
firmly in place.
Hook on the top side
Orientate the trim
plate as illustrated
before fitting.
Dashboard of your car