Kenwood KTC-HR200 Instruction Manual - Page 16

Troubleshooting Guide - hd radio tuner

Get Kenwood KTC-HR200 - HD Radio Tuner Box PDF manuals and user guides
UPC - 019048178886
View all Kenwood KTC-HR200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Troubleshooting Guide What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. oThe HD Radio mode cannot be selected. ttl' The connection wire is not connected. 1& Use the connection wire to connect the control o---------u-n-i-t -a-n-d-t-h-e-H-D--R-a-d-i-o-t-un-e-r-.Nothing happens when the buttons are pressed. ttl' The computer chip in the unit is not functioning normally. 1& Press the reset button on the Control/Controller unit. oNo sound can be heard, or the volume is low. ttl' The input/output wires or wiring harness are connected incorrectly. .... Reconnect the input/output wires and/or the wiring harness correctly. See the section on c;:.~r:t.r1.~S::! ~~.g..'{1!!!~~. ~5?.I~!.~!~~Is>. ttl' The preset broadcast station is not transmitting in the mode that was set with . .... Please set to "Auto ttl' It switches between the Digital broadcasting and Analog broadcasting too often. 1& If the receiving condition is bad,

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
Troubleshooting Guide
~
~
The messages shown
below
display your
systems condition.
In
HD
Radio
mode, the display
of
Station Name or Song
title should
be
set
up.
The
channel information cannot
be
displayed
in
the Frequency display. (page En-6/8/11)
HD#
Off/
#CH
Off/
OFF:
The
Sub
channel, which cannot
be
used,
was
selected.
<Receive
Mode>
is
set
to
"Analog";
therefore, the channel cannot be
used.
¢
Set
<Receive
Mode>
(page
En-5/1
0/13)
to "Auto" or "Digital".
Although the
Sub
channel
was
selected, it
is
under reading or
has
not been received.
Linking:
What
might
appear to be a malfunction
in
your
unit may just be
the
result
of
slight misoperation
or miswiring. Before calling service, first check the
following table for possible problems.
o
The HD Radio
mode
cannot be selected.
ttl'
The connection wire
is
not
connected.
1&
Use
the connection wire to connect the control
unit
and the
HD
Radio tuner.
--------------------------------
o
Nothing happens when
the
buttons are pressed.
ttl'
The
computer
chip
in
the unit
is
not functioning
normally.
1&
Press
the reset
button
on the Control/Controller
unit.
o
No
sound can be heard,
or
the
volume
is
low.
ttl'
The
input/output
wires or wiring harness
are
connected incorrectly.
....
Reconnect the
input/output
wires
and/or
the
wiring harness correctly.
See
the section on
............
:..
c;:.~r:t.r1.~S::!
~~.g
..
'{1!!!~~.
~5?.I~!.~!~~
I
s>
.
ttl'
The preset broadcast station
is
not
transmitting
in
the
mode
that
was set
with
<Receive
Mode>.
....
Please
set <Receive Mode> to "Auto".
--------------------------------------------.----------
ttl'
It switches between the Digital broadcasting and
Analog broadcasting too often.
1&
If
the receiving condition
is
bad, <Receive
............
~5?g~?_.~.~5?~!s!.~~
..
~~.~.~<?~~f::.r1.~log"
ttl'
In
digital AM broadcasting, receive mode switches
between stereo and monaural too often.
1&
Receiving condition
is
bad or unstable. Stereo
is
chosen when receiving condition
is
good, and
it switches
to
monaural when the condition
becomes bad
------------._----.--.
__
._._---------------------------
ttl'
The source mode
was
changed or the power switch
was
turned on.
1&
The monaural signals
are
received several
seconds after power·on or after
FM
tuning to
an
HD Radio station.
--------------------------------
o
Radio reception
is
poor.
ttl'
The car antenna
is
not
extended.
1&
Pull
the antenna
out
all the
way.
·~··Tr)e·anter)na·c·o·n·t·rorwi·re·is··not·connected.
1&
Connect the wire correctly, referring to the
section on <Connecting
Wires
to Terminals>.
--------------------------------
o
The
tuner
cannot be used by
the
Dual Zone
System.
ttl'
The
HD
Radio source cannot be selected by the Dual
Zone System.
1&
An
internal source other than Tuner can be
selected.
En-16
I
KTC-HR200