Kenwood TK 3230 Instruction Manual - Page 26

Scanning The Channels

Get Kenwood TK 3230 - FreeTalk XLS UHF PDF manuals and user guides
UPC - 019048173591
View all Kenwood TK 3230 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Scanning the Channels You can scan the transceiver channels to search for a signal. When the transceiver verifies a signal on a channel, it proceeds to check whether or not its QT/ DQT setting matches that which is set up on your transceiver (if you have set a channel with QT/ DQT). If the QT/ DQT matches, the transceiver stops at the channel and opens the squelch so you can listen to the call. If the QT/ DQT does not match, the call is ignored and scanning continues. Before you can use the scan function, ensure that it is activated. You can turn the scan function (the ability to perform scan) ON or OFF in Setting mode. 1 With the transceiver power OFF, press and hold the MENU key while turning the transceiver power ON (for 1 second). 2 Press the or key to select "SC". 3 Press the MENU key then press or to select "SC-oF" (scan function disabled) or "SC-on" (scan function enabled). • If you select "SC-oF", you will no longer be able to perform scan by pressing and holding the key {page 18}. 4 Press the MENU key to confirm the selection. 5 Press the PTT, MON, or CAL key to exit Setting Mode. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
±7
SCANNING THE CHANNELS
You can scan the transceiver channels to search for a signal.
When the transceiver verifies a signal on a channel, it proceeds
to check whether or not its QT/ DQT setting matches that
which is set up on your transceiver (if you have set a channel
with QT/ DQT).
If the QT/ DQT matches, the transceiver stops
at the channel and opens the squelch so you can listen to the
call.
If the QT/ DQT does not match, the call is ignored and
scanning continues.
Before you can use the scan function, ensure that it is
activated.
You can turn the scan function (the ability to perform
scan) ON or OFF in Setting mode.
±
With the transceiver power OFF, press and hold the
MENU
key while turning the transceiver power ON (for 1 second).
²
Press the
or
key to select “SC”.
³
Press the
MENU
key then press
or
to select “SC-oF”
(scan function disabled) or “SC-on” (scan function enabled).
•
If you select “SC-oF”, you will no longer be able to perform
scan by pressing and holding the
key {page 18}.
´
Press the
MENU
key to confirm the selection.
µ
Press the
PTT
,
MON
, or
CAL
key to exit Setting Mode.