Kenwood TK 3230 Instruction Manual - Page 27

Revert Channel

Get Kenwood TK 3230 - FreeTalk XLS UHF PDF manuals and user guides
UPC - 019048173591
View all Kenwood TK 3230 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

To begin scanning: 1 Press and hold the key for 1 second. • "SCAn" appears on the display. 2 When a signal is detected and the QT/ DQT matches, the channel number appears on the display and blinks. 3 When the signal is no longer present, the transceiver waits for 5 seconds before scanning continues. • If a new signal appears before the 5 seconds elapse, the transceiver will remain on the channel until the new signal is no longer present, at which time it will again wait for 5 seconds before continuing. 4 To end the scan at any time, press and hold the key for 1 second. • The transceiver returns to the channel you were using before you started scanning. Revert Channel The revert channel is the channel from which you start scanning. So, for example, if you are on channel 1 when you begin to scan, your revert channel is channel 1. During scan, pressing the PTT switch will automatically select the transceiver's revert channel (in the above example, channel 1) and you will begin transmitting. However, if you are currently paused on another channel after having received a signal (for example, channel 2), pressing the PTT switch will allow you to transmit on that channel, rather than returning to the revert channel. Scanning will resume after 5 seconds, unless a signal is present on the channel. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
±8
To begin scanning:
±
Press and hold the
key for 1 second.
•
“SCAn” appears on the display.
²
When a signal is detected and the QT/ DQT matches, the
channel number appears on the display and blinks.
³
When the signal is no longer present, the transceiver waits
for 5 seconds before scanning continues.
•
If a new signal appears before the 5 seconds elapse, the
transceiver will remain on the channel until the new signal is
no longer present, at which time it will again wait for 5 seconds
before continuing.
´
To end the scan at any time, press and hold the
key for
1 second.
•
The transceiver returns to the channel you were using before
you started scanning.
R
EVERT
C
HANNEL
The revert channel is the channel from which you start
scanning.
So, for example, if you are on channel 1 when you
begin to scan, your revert channel is channel 1.
During scan, pressing the
PTT
switch will automatically
select the transceiver’s revert channel (in the above example,
channel 1) and you will begin transmitting.
However, if you are
currently paused on another channel after having received a
signal (for example, channel 2), pressing the
PTT
switch will
allow you to transmit on that channel, rather than returning
to the revert channel.
Scanning will resume after 5 seconds,
unless a signal is present on the channel.