Kenwood TM-281A User Manual - Page 50

Scan Resume Method

Get Kenwood TM-281A PDF manuals and user guides View all Kenwood TM-281A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

SCAN RESUME METHOD The transceiver stops scanning at the frequency (or Memory Channel) where a signal is detected. It then continues or stops scanning according to which Resume Mode you have selected. • Time-Operated Mode (default) The transceiver remains on a busy frequency (or Memory Channel) for approximately 5 seconds, then continues to scan even if the signal is still present. • Carrier-Operated Mode The transceiver remains on a busy frequency (or Memory Channel) until the signal drops out. There is a 2-second delay between signal dropout and scan resumption. • Seek Mode The transceiver moves to a frequency (or Memory Channel) where a signal is present and stops. To change the scan resume method: 1 Press [F], [MENU] and turn the Tuning control to select Menu No. 13 (SCAN). 2 Press [MENU] and turn the Tuning control to select "TO" (Time-Operated; default), "CO" (CarrierOperated), or "SE" (Seek) Mode. 3 Press [MENU] to store the new setting or any other key to cancel. 4 Press any key other than [MENU] to exit Menu Mode. Note: To temporarily stop scanning and monitor weak signals, press the Mic PF key assigned the MONI function {page 57}. Press the MONI key again to resume scanning. 8 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
43
8
SCAN RESUME METHOD
The transceiver stops scanning at the frequency (or
Memory Channel) where a signal is detected.
It then
continues or stops scanning according to which Resume
Mode you have selected.
•
Time-Operated Mode (default)
The transceiver remains on a busy frequency (or
Memory Channel) for approximately 5 seconds, then
continues to scan even if the signal is still present.
•
Carrier-Operated Mode
The transceiver remains on a busy frequency (or
Memory Channel) until the signal drops out.
There is
a 2-second delay between signal dropout and scan
resumption.
•
Seek Mode
The transceiver moves to a frequency (or Memory
Channel) where a signal is present and stops.
To change the scan resume method:
1
Press
[F]
,
[MENU]
and turn the
Tuning
control to
select Menu No. 13 (SCAN).
2
Press
[MENU]
and turn the
Tuning
control to
select “TO” (Time-Operated; default), “CO” (Carrier-
Operated), or “SE” (Seek) Mode.
3
Press
[MENU]
to store the new setting or any other
key to cancel.
4
Press any key other than
[MENU]
to exit Menu Mode.
Note:
To temporarily stop scanning and monitor weak signals, press
the Mic PF key assigned the MONI function {page 57}.
Press the
MONI key again to resume scanning.