Kenwood TS-480SAT Operation Manual - Page 18
Getting Acquainted
View all Kenwood TS-480SAT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 18 highlights
GETTING ACQUAINTED REMOTE CONTROL PANEL w e r t q u i o !0 HF/50MHz ALL MODE TRANSCEIVER TS-480 PF ANT 1/2 ATT/PRE AT AF SQL 1 REC 2 REC CH1 CH2 4 TX MONI 5 RF.G PWR MIC 7 8 NB/T VOX CLR 0 OFF MTR AGC 3 REC CH3 6 DELAY KEY 9 PROC ENT DNL NAR NR FIL BC CW.T STEP SG.SEL FINE SCAN MODE F.LOCK MENU MHz CL XIT RIT M.IN QMI M VFO QMR M/V A / B SPLIT A=B TF-SET MULTI IF SHIFT y !1 !2 !3 q [ ] (POWER) switch Press and hold briefly to switch the transceiver power ON. Press again to switch the power OFF {page 18}. w PF key You can assign a function to this Programmable Function key. The default function is VOICE1. To use the Voice Guide and Storage functions, the optional VGS-1 is required {page 64}. e ATT/PRE/ ANT1/2 key Press to cycle between receiver attenuator ON, preamplifier ON and OFF {pages 49, 61}. Press and hold for 1 second, then release it to select either ANT 1 or ANT 2 {page 60}. r AT Press to activate the internal antenna tuner {page 60} or an external antenna tuner. Press and hold to start tuning the automatic antenna tuner. t SQL control Used for muting ("squelching") the speaker, the head phones and the AF output on DATA (8-pin mini DIN connector) when no receive signal is present on the transceiver {page 19}. y AF control Turn to adjust the audio volume on the transceiver {page 18}. u CH1/ 1/ REC, CH2/ 2/ REC, CH3/ 3/ REC key Press to play back the CW or voice messages (the VGS-1 is required) {page 40}. Press and hold to record the voice messages (the VGS-1 is required) {page 68} or CW messages that are associated with the internal electronic keyer {page 40}. i PWR/ 4/ TX MONI key Press to adjust the transmission output power. Press and hold to adjust the volume of the transmission signal monitor function {page 65}. o MIC/ 5/ RF.G key Press to adjust the microphone gain {page 27}. While the Speech Processor function is ON, press to adjust the Speech Processor output level {page 37}. Press and hold to adjust the receiver RF gain {page 18}. !0 KEY/ 6/ DELAY key Press to adjust the internal electronic keyer speed. Press and hold to adjust the VOX delay time {page 36} or Break-in time (Full Break-in/ Semi Break-in time) for CW mode {page 39}. !1 NB/T/ 7 key Press to switch the Noise Blanker ON or OFF. Press and hold to adjust the Noise Blanker level {page 47}. In FM mode, press to turn the Tone function ON or OFF {page 32}. Press and hold to select a sub-audible tone for the Tone funtion {page 32}. !2 VOX/ 8 key In voice mode, press to turn the VOX (VoiceOperated Transmit) function ON or OFF {page 36}. In CW mode, press to turn the Break-in function ON or OFF {page 39}. Press and hold to adjust the microphone input gain for VOX operation. The VOX icon appears when the VOX (Voice)/ Break-in (CW) function is active. !3 PROC/ 9 key Press to turn the Speech Processor ON or OFF {page 37}. Press and hold to adjust the Speech Processor input level. The PROC icon appears when the Speech Processor function is ON. 10