Kenwood TS-480SAT Operation Manual - Page 21

Lcd Display

Get Kenwood TS-480SAT PDF manuals and user guides View all Kenwood TS-480SAT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

LCD DISPLAY 3 GETTING ACQUAINTED q w e r t y u i o !0 !1 !2 !3 !4 !5 !6 !7 !8!9 q METER While receiving, serves as an S-meter to measure and display the received signal strength. While transmitting, serves as a power meter plus an ALC meter, an SWR meter, or a Speech Processor compression meter. The Peak Hold function holds each reading for approximately half a second. w RtATsT Appears while the internal antenna tuner {page 60} or an external antenna tuner is in-line for the operation. e 1tANTs2 Either "1tANT" or "ANTs2" appears, depending on which antenna connector is selected for the operation {page 60}. r ATT Appears when the receiver's attenuator (approx. 12 dB) is ON {pages 49, 61}. t PRE Appears when the receiver pre-amplifier (approx. 6 dB) is ON {page 49}. y VOX Appears when the VOX (Voice Operated Transmission) function is ON or the Break-in function is ON for the CW mode {pages 36, 39}. u PROC Appears when the Speech Processor function is ON {page 37}. i MENU Appears when configuring the parameters in the Menu mode {page 22}. o Reserved for future updates. !0 Appears while the Constant Recording function is working {page 69}. !1 NB Appears when the Noise Blanker is ON {page 47}. !2 AGC OFF "AGC - F" (fast) or "AGC" (slow) appears when the AGC (Automatic Gain Control) function is ON. "AGC OFF" appears when the AGC is OFF {page 35}. !3 NAR 2 "NAR" appears when the narrow IF filter is selected for the operating mode. If 2 optional IF filters are installed and the transceiver selects the secondary IF filter, "NAR 2" appears {page 45}. !4 MHz Appears when the MHz Up/ Down mode using the MULTI control is ON {page 34}. It also appears when the Quick Menu function is ON {page 22}. !5 FINE Appears when the Fine function is ON {page 35}. !6 Appears when the selected Menu No. is in the Quick Menu list. It also appears when the transceiver is scanning the frequencies between the slow down frequency points {page 57}. !7 Appears when the split-frequency operation is ON {page 30}. !8 Appears when the Tuning control Lock function is ON {page 63}. !9 Appears when the Frequency Lock function is ON {page 63}. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
13
3
GETTING ACQUAINTED
q
METER
While receiving, serves as an S-meter to measure
and display the received signal strength.
While
transmitting, serves as a power meter plus an ALC
meter, an SWR meter, or a Speech Processor
compression meter.
The Peak Hold function holds
each reading for approximately half a second.
w
R
t
AT
s
T
Appears while the internal antenna tuner {page 60} or
an external antenna tuner is in-line for the operation.
e
1
t
ANT
s
2
Either “
1
t
ANT
” or “
ANT
s
2
” appears, depending on
which antenna connector is selected for the operation
{page 60}.
r
ATT
Appears when the receiver’s attenuator (approx.
12 dB) is ON {pages 49, 61}.
t
PRE
Appears when the receiver pre-amplifier (approx.
6 dB) is ON {page 49}.
y
VOX
Appears when the VOX (Voice Operated
Transmission) function is ON or the Break-in function
is ON for the CW mode {pages 36, 39}.
u
PROC
Appears when the Speech Processor function is ON
{page 37}.
i
MENU
Appears when configuring the parameters in the
Menu mode {page 22}.
o
Reserved for future updates.
q
w
e
r
t
y
u
o
!
0
!
1
!
4
!
5
!
6
!
7
!
8
!
9
i
!
2
!
3
!0
Appears while the Constant Recording function is
working {page 69}.
!1
NB
Appears when the Noise Blanker is ON {page 47}.
!2
AGC OFF
“AGC
- F” (fast) or “AGC” (slow) appears when the
AGC (Automatic Gain Control) function is ON.
“AGC
OFF” appears when the AGC is OFF {page 35}.
!3
NAR 2
“NAR” appears when the narrow IF filter is selected
for the operating mode.
If 2 optional IF filters are
installed and the transceiver selects the secondary IF
filter, “NAR 2” appears {page 45}.
!4
MHz
Appears when the MHz Up/ Down mode using the
MULTI
control is ON {page 34}.
It also appears when
the Quick Menu function is ON {page 22}.
!5
FINE
Appears when the Fine function is ON {page 35}.
!6
Appears when the selected Menu No. is in the Quick
Menu list.
It also appears when the transceiver is
scanning the frequencies between the slow down
frequency points {page 57}.
!7
Appears when the split-frequency operation is ON
{page 30}.
!8
Appears when the
Tuning
control Lock function is ON
{page 63}.
!9
Appears when the Frequency Lock function is ON
{page 63}.
LCD DISPLAY