Kenwood VR-509 User Manual - Page 20

Preparing for surround sound Speaker settings 20 To enable you to obtain optimum enjoyment from the receiver's listening modes, make sure to complete the speaker settings (subwoofer, front, center, and surround speakers) as described below. MULTI CONTROL SET UP Preparations POWER ( ) Display operation 1 5/∞ Display operation 2 SYS. POWER ( ) + + - - 1 Turn on the power to this receiver by pressing POWER ( ) or SYS. POWER ( ) key. 2 Select a speaker system. 1 Press the SET UP key such that the subwoofer setting indication (SUBW ON) appears. SP A B TI.VOL CLIP MUTE RDS EON PTY TP TA NEWS L CR LFE SW LS S RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO MHz 3 STEREO MONITOR ST. kHz DOWN MIX DSP TUNED When you operate on the remote control unit 1 Press the display operation 2 [Menu] key repeatedly until "01.IR" appears in the display of the remote control unit. >01.IR >02.Surround Home Enter 2 Press the 5/∞ keys to select "02.Surround", then press the display operation 2 [Enter] key. SetUp Home Next 2 Use the MULTI CONTROL knob or 5/∞ keys to select the appropriate subwoofer setting. 1 SUBW ON : Subwoofer setting mode to the receiver is ON. 2 SUBW OFF : Subwoofer setting mode to the receiver is OFF. • The initial setting is "SUBW ON". • When "SUBW OFF" is selected, the front speakers are automatically set to "FRNT LRG" and the procedure skips to step 5. • When subwoofer output sound is required, selected "FRNT NML". 3 Press the SET UP or display operation 2 [Next] key to accept the setting. • The front speakers setting indication (FRNT) appears. SP A B TI.VOL CLIP MUTE RDS EON PTY TP TA NEWS L CR LFE SW LS S RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO MHz 3 STEREO MONITOR ST. kHz DOWN MIX DSP TUNED 4 Use the MULTI CONTROL knob or 5/∞ keys to select the appropriate front speakers setting. 1 FRNT NML (normal) : Average size front speakers are connected to the receiver. 2 FRNT LRG (large) : Large front speakers are connected to the receiver. • For "FRNT LRG" selection, no sound will be heard from SUBW even when it is set to ON. However, if you select CINEMA EQ. when subwoofer is selected, you will be able to hear sound from the subwoofer. When in STEREO mode, the sound goes directly to front speaker. 5 Press the SET UP or display operation 2 [Next] key to accept the setting. • The center speaker setting indication (CNTR) appears. 6 Use the MULTI CONTROL knob or 5/∞ keys to select the appropriate center speaker setting. If you selected "LRG" as the front speakers setting, 1 CNTR LRG (large) : A large center speaker is connected to the receiver. 2 CNTR NML (normal) : An average size center speaker is connected to the receiver. 3 CNTR OFF : Center speaker setting mode to the receiver is OFF. If you have selected "NML" as the front speakers setting, 1 CNTR ON : Center speaker setting mode to the receiver is ON. 2 CNTR OFF : Center speaker setting mode to the receiver is OFF. 7 Press the SET UP or display operation 2 [Next] key to accept the setting. • The surround speaker setting indication (SURR) appears. 8 Use the MULTI CONTROL knob or 5/∞ keys to select the appropriate surround speaker setting, If you have selected "LRG" as the center speaker setting, 1 SURR LRG (large) : Large surround speakers are connected to the receiver. 2 SURR NML (normal) : Average size surround speakers are connected to the receiver. 3 SURR OFF : Surround speaker setting mode to the receiver is OFF. If you have selected other than "LRG" as the center speaker setting, 1 SURR ON : Surround speaker setting mode to the receiver is ON. 2 SURR OFF : Surround speaker setting mode to the receiver is OFF. 9 Press the SET UP or display operation 2 [Next] key to accept the setting. • The receiver enters the speaker volume level adjustment mode. • In steps 3 and 4, indications appear only for the selected channels of the speakers that require adjusting.