Kenwood VR-509 User Manual - Page 21
Input the distance to the speakers., Input level adjustment analog sources only, Adjust the speaker
View all Kenwood VR-509 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 21 highlights
3 Adjust the speaker volume. From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same. 1 Use the MULTI CONTROL knob or 5/∞ keys to adjust the volume of the test tone output from the speaker channel to be adjusted. The channel indication blinks while the test tone is being output. SP A B TI.VOL CLIP MUTE RDS EON PTY TP TA NEWS L CR LFE LS S RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO MHz 3 STEREO MONITOR ST. kHz DOWN MIX DSP TUNED The test tone is heard from the speakers in the following sequence for 2 seconds each: = L = C = R = SR = SL = SW • If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed º • If the speaker setting selects are OFF, the speaker level settings are reset. 2 Press the SET UP or display operation 2 [Next] key. • The test tone is turned off. The receiver enters the mode for inputting the distance to the speakers. 4Input the distance to the speakers. 1 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to front speakers: Distance to center speaker: Distance to surround speakers: ____ feet (meters) ____ feet (meters) ____ feet (meters) 2 Use the MULTI CONTROL knob or 5/∞ keys to select the distance to the front speakers. The speaker indicator to be adjusted blinks. SP A B TI.VOL CLIP MUTE RDS EON PTY TP TA NEWS LCR LFE SW LS S RS Indication in feet FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO MHz 3 STEREO MONITOR ST. kHz DOWN MIX DSP TUNED Indication in meters • The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable in 1 foot (0.3 m) increments. 3 Press the SET UP or display operation 2 [Next] key. 4 Repeat steps 2 and 3 to input the distance for each of the speakers. 5 Setup is complete when the input indication reappears. SP A B TI.VOL CLIP MUTE RDS EON PTY TP TA NEWS L CR LFE SW LS S RS Display when all speakers have been selected. • The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected. Preparing for surround sound Input level adjustment (analog sources only) 21 If the input level of an analog source signal is too high, the CLIP indicator will blink. Adjust the input level. Preparations CLIP RDS TP 1 Use the INPUT SELECTOR knob to select the source which input level you want to adjust. • You can store a separate input level for each input source. If the MONITOR function is ON, you can store an input level for when MONITOR is on independently of the input levels for the input sources. 2 Press the SOUND key repeatedly until the "INPUT" indication appears. 3 Use the MULTI CONTROL knob or 5/∞ keys to adjust the input level. SP A B TI.VOL CLIP MUTE RDS EON PTY TP TA NEWS L CR LFE SSWW LS S RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO MHz 3 STEREO MONITOR ST. kHz DOWN MIX DSP TUNED • The adjustment mode is displayed for approximately eight seconds. • The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB.) 4 Press the SOUND key again to return to the input indication.