Kenwood VR-50RS User Manual - Page 17
Preparing for surround sound, Adjust the speaker volume level., Input the distance to the speakers.
View all Kenwood VR-50RS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
Preparing for surround sound If you have selected "NML" as the Front speakers setting, 1 CNTR NML (normal) : An average size Center speaker is connected to this model. 2 CNTR OFF : Center speaker setting mode to this model is OFF. 9 Press the SETUP key again to accept the setting. •The surround speaker setting indication "SURR NML" appears. 0 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to select the appropriate Surround speaker setting. If you have selected "LRG" as the Center speaker setting, 1 SURR NML (normal) : Average size Surround speakers are connected to this model. 2 SURR LRG (large) : Large Surround speakers are connected to this model. 3 SURR OFF : Surround speaker setting mode to this model is OFF. If you have selected other than "LRG" as the Center speaker setting, 1 SURR NML (normal): Average size Surround speakers are connected to this model. 2 SURR OFF : Surround speaker setting mode to this model is OFF. • When the setting "SURR OFF" is selected, the procedure skips to step #. ! Press the SETUP key to accept the setting. • The Surround Back speaker setting indication "BS" appears. @ Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to select the appropriate Surround Back speaker setting. If you have selected "LRG" as the surround speaker setting, 1 BS NML (normal : Average size Surround back speakers are connected to this model. 2 BS LRG (large) : Large Surround Back speaker is connected to this model. 3 BS OFF : Surround Back speaker setting mode to this model is OFF. If you have selected "NML" as the Surround speaker setting, 1 BS NML (normal) : Average size Surround Back speakers are connected to this model. 2 BS OFF : Surround Back speaker setting mode to this model is OFF. (VR-60RS only) If you have selected "LRG" or "NML" as the surround back speaker setting. 1 SPEAKER : Surround Back signal will be output from SURROUND BACK speaker terminal, and SURR BACK L/ SURR BACK PRE OUT terminal as monaural. 2 PRE OUT : Surround Back signals will be output from SURR BACK L/ SURR BACK and SURR BACK R PREOUT terminals as stereo. # Press the SETUP key again to accept the setting. • The subwoofer re-mix setting indication "SW RE-MIX" scrolls across the display. • If subwoofer is turned OFF, subwoofer re-mix setting is not visible. $ Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to select the appropriate Subwoofer re-mix setting. 1 RMX ON : Subwoofer re-mix set mode to this model is ON. 2 RMX OFF : Subwoofer re-mix set mode to this model is OFF. % Press the SETUP key to accept the setting. 4 Adjust the speaker volume level. From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same. • In step 4 and 5, indications appear only for the selected channels of the speakers that require adjusting. 1 Press the SETUP key to begin TEST TONE. • This model enters the speaker volume level adjustment mode. The selection of AUTO/MANUAL TEST TONE is done by the MULTI CONTROL knob or MULTI CONTROL %/fi keys. 1 AUTO 2 MANUAL 2 Press the SETUP key again to select either AUTO or MANUAL. Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to adjust the volume level of the test tone output from the speaker channel to be adjusted. For AUTO selection, the test tone is heard from the speakers in the following sequence for 2 seconds each: • If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. ¶ • If any of the speaker is set as OFF during SP SET UP, the TEST TONE adjustment for the speaker will be skipped. (VR-60RS only) • If you have selected "SPEAKER" as the Surround Back setting, "RB" and "LB" are not appeared but "BS" is appeared. 3 Press the SETUP key. • The test tone is turned off. This model enters the mode for inputting the distance to the speakers. 4 For MANUAL selection, press the SETUP key each time to select the speaker channel. 5 Input the distance to the speakers. 1 Select the DISTANCE from the set up displays and press the SETUP key again. 2 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to Front Left speaker (L) : ____ feet (meters) Distance to Center speaker (C) : ____ feet (meters) Distance to Front Right speaker (R) : ____ feet (meters) Distance to Surround Right (RS) : ____ feet (meters) Distance to Surround Back Right (RB) : ____ feet (meters) Distance to Surround Back (BS) : ____ feet (meters) Distance to Surround Back Left (LB) : ____ feet (meters) Distance to Surround Left (LS) : ____ feet (meters) Distance to Subwoofer (SW) : ____ feet (meters) (VR-60RS only) • If you have selected "SPEAKER" as the Surround Back setting, "RB" and "LB" are not appeared but "BS" is appeared. Continued to next page 17 EN