KitchenAid KDRS463VBK Installation Instructions - Page 21

Reinstall Kick Plate, Complete Installation

Get KitchenAid KDRS463VBK PDF manuals and user guides View all KitchenAid KDRS463VBK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

11. When finished adjusting the flame height, put a control knob back onto the valve stem and turn off the burner. 12. Remove the control knob. 13. Replace the round gasket. 14. Repeat steps 6 through 13 for any other burners that need adjustment. 15. Lift up on the control console and set it back into place. For a proper fit, the flange of the control console must hook over the lip on the front of the range cooktop. A B A. Control console flange B. Front lip of range cooktop 16. Check that the control console is flush with the top edge of the range. A A. Flush with range top 17. Replace the 2 screws on each side of the control console. 18. Replace the control knobs. 19. Replace burner grates. 20. Test the flame by turning the control from LO to HI, checking the flame at each setting. Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. For oven use and cleaning, read the Use and Care Guide. Check Operation of Oven(s) 1. Turn power on. 2. Start a Bake cycle. See the Use and Care Guide for operating instructions. If oven(s) does not operate, check the following: ■■ Household fuse is intact and tight or circuit breaker has not tripped. ■■ Electrical supply is connected. ■■ See "Troubleshooting" section in the Use and Care Guide. 3. When oven has been on for 10-15 minutes, open the oven door and feel for heat. If you do not feel heat or if an error code ("F" followed by a number plus "E" followed by a number) appears in the display, turn off the oven and contact a qualified technician. 4. Touch OFF. To set the clock and other oven functions, refer to the Use and Care Guide. If you need Assistance or Service: Please reference the "Assistance or Service" section of the Use and Care Guide or contact the dealer from whom you purchased your range. Reinstall Kick Plate 1. Align shoulder screw mounting holes with shoulder screws on range. 2. Push kick plate down against front of range until the top screw holes are aligned with the mounting holes on the front of the range. 3. Reattach screws to the top of the kick plate. B C A D A. Kick plate B. Reattach these screws. C. Top screw hole D. Shoulder screw mounting hole 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
21
16.
Check that the control console is flush with the top edge
of the range.
A
17.
Replace the 2 screws on each side of the control console.
18.
Replace the control knobs.
19.
Replace burner grates.
20.
Test the flame by turning the control from LO to HI,
checking the flame at each setting.
Reinstall Kick Plate
1.
Align shoulder screw mounting holes with shoulder screws
on range.
2.
Push kick plate down against front of range until the top
screw holes are aligned with the mounting holes on the
front of the range.
3.
Reattach screws to the top of the kick plate.
A
B
D
C
A. Kick plate
B. Reattach these screws.
C. Top screw hole
D. Shoulder screw mounting hole
11.
When finished adjusting the flame height, put a control
knob back onto the valve stem and turn off the burner.
12.
Remove the control knob.
13.
Replace the round gasket.
14.
Repeat steps 6 through 13 for any other burners that
need adjustment.
15.
Lift up on the control console and set it back into place.
For a proper fit, the flange of the control console must hook
over the lip on the front of the range cooktop.
A
B
A. Control console flange
B. Front lip of range cooktop
A. Flush with range top
Complete Installation
1.
Check that all parts are now installed. If there is an
extra part, go back through the steps to see which
step was skipped.
2.
Check that you have all of your tools.
3.
Dispose of/recycle all packaging materials.
4.
For oven use and cleaning, read the Use and Care Guide.
Check Operation of Oven(s)
1.
Turn power on.
2.
Start a Bake cycle. See the Use and Care Guide for
operating instructions.
If oven(s) does not operate, check the following:
■
Household fuse is intact and tight or circuit breaker
has not tripped.
■
Electrical supply is connected.
■
See “Troubleshooting” section in the Use and Care
Guide.
3.
When oven has been on for 10–15 minutes, open the oven
door and feel for heat.
If you do not feel heat or if an error code (“F” followed by
a number plus “E” followed by a number) appears in the
display, turn off the oven and contact a qualified technician.
4.
Touch OFF.
To set the clock and other oven functions, refer to the
Use and Care Guide.
If you need Assistance or Service:
Please reference the “Assistance or Service” section of the
Use and Care Guide or contact the dealer from whom you
purchased your range.