KitchenAid KURO24RSBX Use & Care Guide - Page 5

Warning - panel

Page 5 highlights

Door Hinge Holes ■ The views of the top and bottom hinge pin hole show a righthand hinge. Mirror the image for a left-hand hinge. ■ We recommend using a C-clamp and two pieces of scrap wood (front and back) to help reinforce the overlay panel when drilling the hinge pin holes. 1. Using a ³⁄₈" Brad point doweling drill bit, drill a hole 7.1 mm) deep, into the top of the overlay panel for the top hinge pin. Remove the excess wood, surrounding the hole, by using the rotary tool to complete the hinge depression as shown. Top View 12 mm) NOTE: It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source. Do not install in a location where the temperature will fall below 55°F (13°C). For best performance, do not install the refrigerator behind a cabinet door or block the base grille. ¹⁄₄" (6.35 mm) A Front Surface 5.5 mm) Back Surface ³⁄₈" (9.5 mm) A. Diameter ³⁄₈" (9.5 mm) 2. Using a ³⁄₈" Brad point doweling drill bit, drill a hole 7.1 mm) deep, in the bottom of the overlay frame for the bottom hinge pin. Remove the excess wood, surrounding the hole, by using the rotary tool to complete the hinge depression as shown. Bottom View 5.5 mm) ³⁄₈" (9.5 mm) Back Surface A Front Surface 12 mm) A. Diameter ³⁄₈" (9.5 mm) Location Requirements WARNING 2¹⁄₂" (6.35 cm) Electrical Requirements WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection. Recommended grounding method A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord. NOTE: Before performing any type of installation, cleaning, or removing a light bulb, unplug refrigerator or disconnect power. Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can result in death, explosion, or fire. To ensure proper ventilation for your refrigerator, allow for a ¹/₄" (6.35 mm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2¹⁄₂" (6.35 cm) minimum clearance on the hinge side to allow for the door to swing open. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40

5
Door Hinge Holes
The views of the top and bottom hinge pin hole show a right-
hand hinge. Mirror the image for a left-hand hinge.
We recommend using a C-clamp and two pieces of scrap
wood (front and back) to help reinforce the overlay panel when
drilling the hinge pin holes.
1.
Using a
³⁄₈
" Brad point doweling drill bit, drill a hole,
⁹⁄₃₂
"
(7.1 mm) deep, into the top of the overlay panel for the top
hinge pin. Remove the excess wood, surrounding the hole, by
using the rotary tool to complete the hinge depression as
shown.
Top View
2.
Using a
³⁄₈
" Brad point doweling drill bit, drill a hole,
⁹⁄₃₂
"
(7.1 mm) deep, in the bottom of the overlay frame for the
bottom hinge pin. Remove the excess wood, surrounding the
hole, by using the rotary tool to complete the hinge
depression as shown.
Bottom View
Location Requirements
To ensure proper ventilation for your refrigerator, allow for a
¹
/
"
(6.35 mm) space on each side and at the top. When installing your
refrigerator next to a fixed wall, leave 2
¹⁄₂
" (6.35 cm) minimum
clearance on the hinge side to allow for the door to swing open.
NOTE:
It is recommended that you do not install the refrigerator
near an oven, radiator, or other heat source. Do not install in a
location where the temperature will fall below 55°F (13°C). For
best performance, do not install the refrigerator behind a cabinet
door or block the base grille.
Electrical Requirements
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.
Recommended grounding method
A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
NOTE:
Before performing any type of installation, cleaning, or
removing a light bulb, unplug refrigerator or disconnect power.
A. Diameter
³⁄₈
" (9.5 mm)
A. Diameter
³⁄₈
" (9.5 mm)
¹⁵⁄₃₂
"
(12 mm)
⁷⁄₃₂
"
(5.5 mm)
A
Back Surface
Front Surface
³⁄₈
"
(9.5 mm)
Front Surface
Back Surface
¹⁵⁄₃₂
"
(12 mm)
⁷⁄₃₂
"
(5.5 mm)
A
³⁄₈
"
(9.5 mm)
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
¹⁄₄
" (6.35 mm)
2
¹⁄₂
" (6.35 cm)
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING