Konica Minolta KIP C7800 User Manual - Page 10

Chapter 1

Before Use

1-2

1. 1

Installation Requirements

The following conditions are required for installation of the equipment.

(1)

Power source should be as follows (according to your region).

U.S.A. / Europe

220 to 240V (+6% to -10%), 20A or higher, and 50/60Hz

(2)

The equipment must be on an exclusive circuit.

The outlet must be near the equipment and easy accessible.

(3)

Make sure to connect this equipment to a grounded outlet.

(4)

The site temperature range = 15 to 27 degrees centigrade, with the humidity between 20% to

70% RH (NON CONDENSING).

Keep the equipment away from water sources, boilers, humidifiers or refrigerators.

(5)

The installation site must not have open flames, dust or ammonia gases.

(6)

The equipment should not be exposed to the direct sunlight.

Please draw curtains to block any sunlight.

(7)

Ozone will be generated while this equipment is in use, although the quantity generated is

within safe levels. (see certifications)

Ventilate the room, if required.

(8)

Levelling Bolts on the bottom of the KIP C7800 should touch the floor correctly.

And the equipment must be levelled.

Floor strength must be ample to sustain the weight of the equipment.

(9)

Keep ample room around the equipment to ensure comfortable operation.

Required space is noted.

120cm (48”)

or wider

150cm (59”) or wider

65cm (26”)

or wider

Rear

Front


(When optional Auto Stacker is

used.)


(When accessory Tray is used)

Section	Page
KIP C7800 User Manual (A.1)	1
Safety Warning	3
WARNING	4
CAUTION	5
POWER CORD INSTRUCTION	6
Chapter 1 Before Use	9
1. 1 Installation Requirements	10
1. 2 Originals Prohibited from Duplication	11
1. 3 Features	12
1. 4 Specifications	13
1. 5 Appearance	15
1. 5. 1 Front view	15
1. 5. 2 Left side view	16
1. 5. 3 Rear view	17
1. 6 Specifications for the Printing Paper	19
1. 6. 1 Papers not available to use	19
1. 6. 2 Keeping the paper in the custody	20
1. 6. 3 Treatment against environmental condition	21
Chapter 2 Basic Operations	22
2. 1 Turning on the KIP C7800	23
2. 2 Turning off the KIP C7800	25
2. 3 Replacing the Roll Media	27
2. 4 Setting Cut Sheet Media to Bypass Feeder	32
2. 4. 1 Loading Small Size Sheet	33
2. 4. 2 Loading Large Size Sheet	35
2. 5 Replacing the Toner Cartridge	37
2. 6 Replacing the Waste Toner Box	41
2. 7 Initial Cut (Straighten the leading edge of roll media)	45
2. 8 Sleep Mode	47
Chapter 3 Troubleshooting	48
3. 1 Mis-feed Errors	49
3. 1. 1 How to Remove Mis-fed Media	50
3. 2 Open Errors	58
3. 2. 1 Roll Deck 1 Open	58
3. 2. 2 Roll Deck 2 Open	58
3. 2. 3 Roll Deck 3 Open	59
3. 2. 4 Roll Deck 1 - Cutter Cover Open	59
3. 2. 5 Roll Deck 2 - Cutter Cover Open	60
3. 2. 6 Roll Deck 3 - Cutter Cover Open	60
3. 2. 7 Sheet Bypass Open	61
3. 2. 8 Left Door Open	61
3. 2. 9 Rear Door Open	62
3. 2.10 Fuser Exit Door Open	62
3. 3 Other Operator Call Error	63
3. 3. 1 Printer out of paper	63
3. 3. 2 Printer out of toner	63
3. 3. 3 Printer waste toner bottle full	64
3. 3. 4 Web Cleaner Empty	65

Konica Minolta KIP C7800 User Manual - Page 10

Installation Requirements - weight

Page 10 highlights