Kyocera FS 1010 FS-1010 Operation Guide Rev-1.2 - Page 28

KM-NET for Clients Operation, Guide, KM-NET, for Clients, KM-NET for Clients - kit roller

Get Kyocera FS 1010 - B/W Laser Printer PDF manuals and user guides View all Kyocera FS 1010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Printed Results Faint or blurred printing Grey background. Dirt on the top edge or back of the paper Characters out of position. Print Quality Problems Corrective Action Check the EcoPrint setting. When this setting is On, switch it to Off on the KM-NET for Clients. (See the KM-NET for Clients Operation Guide) Confirm the (toner) indicator. If the (toner) indicator flashes, install a new toner kit. (See Chapter 2) Clean the charger wire. Open the printer's top and front covers. Remove the process unit from the printer and slide the charger knob back and forth to clean the charger wire. (See Chapter 2) Try setting the thin paper mode. Set the paper type to Thin in the KM-NET for Clients utility. (See the KM-NET for Clients Operation Guide) Check the operator panel. When the (toner) indicator flashes, install a new toner kit. (See Chapter 2) Check the process unit. Open the printer's top cover and front cover, then check that the process unit is properly installed. Check the transfer roller. Open the printer's top and front covers. Remove the process unit from the printer and check whether the transfer roller is dirty. If so, print several pages to eliminate the dirt. Check the registration roller. Open the printer's top and front covers. Remove the process unit from the printer and check whether the registration roller is soiled with toner. If so, wipe it clean using the supplied wiper cloth. Check the file or program. Check whether the problem is being caused by a PRESCRIBE command error. If the problem occurs only with a specific file or program, the most likely cause is an error in a parameter to a command or command syntax. Check the paper size setting. Check that the paper size set in the paper source and the paper size set on the KM-NET for Clients are the same. (See the KM-NET for Clients Operation Guide) 3-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
Print Quality Problems
3-4
Faint or blurred printing
Check the EcoPrint setting.
When this setting is On, switch it to Off on the
KM-NET
for Clients
. (See the
KM-NET for Clients Operation
Guide
)
Confirm the
(toner) indicator.
If the
(toner) indicator flashes, install a new toner
kit. (See
Chapter 2
)
Clean the charger wire.
Open the printer’s top and front covers. Remove the
process unit from the printer and slide the charger knob
back and forth to clean the charger wire.
(See
Chapter 2
)
Try setting the thin paper mode.
Set the paper type to Thin in the
KM-NET for Clients
utility. (See the
KM-NET for Clients Operation
Guide
)
Grey background.
Check the operator panel.
When the
(toner) indicator flashes, install a new
toner kit. (See
Chapter 2
)
Check the process unit.
Open the printer’s top cover and front cover, then check
that the process unit is properly installed.
Dirt on the top edge or back of the paper
Check the transfer roller.
Open the printer’s top and front covers. Remove the
process unit from the printer and check whether the
transfer roller is dirty. If so, print several pages to
eliminate the dirt.
Check the registration roller.
Open the printer’s top and front covers. Remove the
process unit from the printer and check whether the
registration roller is soiled with toner. If so, wipe it clean
using the supplied wiper cloth.
Characters out of position.
Check the file or program.
Check whether the problem is being caused by a
PRESCRIBE command error. If the problem occurs only
with a specific file or program, the most likely cause is an
error in a parameter to a command or command syntax.
Check the paper size setting.
Check that the paper size set in the paper source and the
paper size set on the
KM-NET for Clients
are the same.
(See the
KM-NET for Clients Operation Guide
)
Printed Results
Corrective Action