Kyocera FS 3700 FS-1700/3700 Users Manual - Page 75

Cleaning, Main Charger Unit, will be displayed after replacement. After - drum unit

Get Kyocera FS 3700 - B/W Laser Printer PDF manuals and user guides View all Kyocera FS 3700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

4.2. Cleaning 4.2. Cleaning In addition to the maintenance procedures described on the following pages, the charger wire in the drum unit and paper feed unit should be cleaned from time to time, or whenever print quality problems occur. To avoid print quality problems, the following printer parts must be cleaned with every toner container replacement.  If the toner container has been replaced when the message Replace Toner Clean printer was displayed, the message Clean printer ..press CONT will be displayed after replacement. After cleaning the inside of the printer following the procedure shown below, press the CONT key; the message will disappear and the printer will be ready for printing. Main Charger Unit The main charger unit grid should be cleaned when the toner container is changed. Cleaning the Charger Wire 1. Open the printer side cover. Main Charger Unit Side Cover 2. Pull the cleaning knob (green ) slowly in Cleaning Knob and out a few times. This pulls a cleaning (Green) pad inside the drum unit along the wire. 4-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
4.2.
Cleaning
In addition to the maintenance procedures described on the following pages, the charger wire
in the drum unit and paper feed unit should be cleaned from time to time, or whenever print
quality problems occur.
To avoid print quality problems, the following printer parts must be cleaned with every toner
container replacement.
If the toner container has been replaced when the message
was displayed, the message
will be displayed after replacement. After
cleaning the inside of the printer following the procedure shown below, press
the
key; the message will disappear and the printer will be ready for
printing.
Main Charger Unit
The main charger unit grid should be cleaned when the toner container is changed.
Cleaning the Charger Wire
1.
Open the printer side cover.
2.
Pull the cleaning knob (
green
) slowly in
and out a few times. This pulls a cleaning
pad inside the drum unit along the wire.
Cleaning Knob
(Green)
Side Cover
Main Charger Unit
4.2.
Cleaning
4-6