LG 42LG700H Owners Manual - Page 100

040 - AUTO CAMPORT Set to I to automatically switch to Camport when equipment is connected to front Video input. Set to 0 to disable front Video automatic source selection. NOTE: If set to I, 093 RJPAvailable is automatically set to 0. 073 - CH NOT AVBLE (Channel Not Available) If set to 1 and item 028 CHANNEL OVERRIDE is set to 0, "NOT AVAILABLE" message is displayed when directly accessing a channel not in the channel scan list available in memory. 046 - STRT AUX SRCE (Start Aux Source) Sets the starting AUX source. At power up, TV will tune to starting Aux source if item 004 Start Channel is set to 0. If item 093 RIPAvailable is set to 0 and item 040 Auto Camport is set to 0: I = Video I 4 = RGB 255 = Last Aux 2 = Video 2 5 = HDMI 2 3 = HDMI I 6 = Component If item 093 RJPAvailableis set at 1: 2 = Video 2 5 = HDMI 2 6 = Component O7S - REVERT CH (Revert to Start Channel) If set to 1 and loss of M.P.I.communication occurs, TV automatically tunes to the specified Start Channel. 078 - UPN MSB (UPN Most Significant Byte) User programmable number, most significant byte readable by M.PJ.command. Note: Not linked to serial number. 079 - UPN MSB-1 (UPN Most Significant Byte-1 ) User programmable number, most significant byte-1 readable by M.P.I.command. Not linked to serial number. If item 040 Auto Camport is set to 1: 1 = Video 1 5 = HDMI 2 3 = HDMI 1 4= RGB 6 = Component 080 - UPN MSB-2 (UPN Most Significant Byte-2) User programmable number, most significant byte-2 readable by M.P.I.command. Not linked to serial number. 047 - AUX STATUS Set to I for M.RI. AUX source to be reported as a channel number instead of channel 0. Set to 0 to disable AUX iden- 081 - UPN LSB (UPN Least Significant Byte) User programmable number, least significant byte readable by M.PJ.command. Not linked to serial number. tification change. Controls M.RI. status channel response for AUX inputs. 082 - CHKSM ERROR (Checksum Error) Enforces rigid M.P.I. checksum validation. Set to 1 for validation. 0S3 - DIS. CH-TIME (Disable Channel-Time) Set to 0 to disable (does not check checksum on M.P.I. Set to I to disable the Channel-Time display, Channel-Time async port). SPI is always checked. display will not appear. Set to 0 to enable the Channel-Time display. 083 - HANDSHK TIME (Handshake Time) N Adds an additional delay to the handshake time which is 64 0 069 - EN. CH-T COL. (Enable Channel-Time Custom msec, thus relaxing M.PJ.timing requirements to be compati- Color) ble with PC based Windows controlled systems, range is 0 - I'rl Set to I to enable custom color for the Channel-Time dis- 5. play. N (Timeout = 25.5MS + [25.5 MS* Handshake time]). Set to 0 to disable custom color for the Channel-Time dis- play. 084 - PERMANENT BLK (Permanent Block) Allows Lock (Parental Control) blocking schemes to be per- 0 070 - FOR. CH-TIME (Channel-Time Display Foreground manent by disabling the blocking hours function. Color) Set to I to install Parental Control restrictions permanently. I-I-I Set according to Color Chart. Set to 0 for user-specified hours control of blocking I-I-I 0 = Black 3 = Yellow 6 = Cyan schemes. -t c I = Red 4 = Blue 7 = White -0 2 = Green 5 = Violet 087 - REAR RGB EN. (Rear RGB Enable) NOTE: If foreground and background color are the same, menu background is transparent. Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 2 for PC for STB RGB input. 071 - BCK. CH-TIME (Channel-Time Display Background Color) Set to 18 for Auto Configure one time only with power cord removal and reinsertion. Set according to Color Chart. 0 = Black 1 = Red 3 = Yellow 4 = Blue 6 = Cyan 7 = White 088 - EN NOISE MUTE (Enable Noise Mute) If set to 1, audio mutes if no signal is present. 2 = Green 5 = Violet NOTE: If foreground and background color are the same, menu background is transparent. 090 - KEY LOCK If set to 1, display panel keyboard is locked ouL not available to end user. IR receiver remains functional. 99