LG 42LG700H Owners Manual - Page 98

Detailed Descriptions of Installer Menu Items 000 - INSTALLERSEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 OOS - CHAN LOCK (Channel Lock) CHAN LOCK is ideal if the system must always be on the same channel. Changing channels with Channel Up/Down or keypad numbers is impossible. Channel Lock is inactive if set to 0 (default). 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The POWER MANAGE function is for saving energy. If set to 0, Power Manage is Off. Settings range from 0 - Z with 1 - 7 representing the hours that the unit will remain On, unless there has been activity from either the control panel or remote control. 002 - AC ON (AC Power Switchable) If set to 1, allows the TV to turn On just by applying AC power. Pressing the On button is not necessary. This is desirable if the TV is plugged into a cable box or a power outlet controlled by a wall switch. Use ADJ Left/Right arrow to choose 0 or 1 where 0 is the default is Off, and 1 is On. Generally, this feature is used in connection with START CHANNEL (Installer item 004) where the start channel may, for example, be set to 3 or 4. If the start channel is 3, then the TV will remain locked on Channel 3. NOTE: For Items 007, 008 and 009 For legacy reasons, the scale used is 0 - 63. The PTC software will translate this to the 0 - 100 scale used by the TV. To translate a TV volume level to the installer menu value, use the following formula: Installer Value = TV Value x 67; 100 NOTE: If set to 1 (On), the TV does not respond to On/Off commands from either the remote or the dis- Enter only the whole number (disregard fractions). play control panel, and the SLEEP TIMER is also nonfunctional. 007 - STRT VOLUME (Start Volume) This function allows the Installer to determine the initial 003 - BAND/AFC (Band/Automatic Frequency Control) There are 4 possible settings for this option: volume level setting when the TV is turned On. This feature is useful for an in-house information channel, since the TV would always select that volume level when it is turned On. The range of values are 0 - 63,255. If 255 0 = Broadcast 2 = HRC 1 = CATV 3 = IRC is selected, the current volume level will be retained in memory when the TV is turned Off; at turn On, the vol- N ume level will be automatically set at the previous or 0 If some channels were not found by Auto Tuning last level. (Channel Search), select the appropriate Band setting I'rl here and add the channels using the Channel Edit 008 - MIN VOLUME (Minimum Volume) N option in the Channel Menu. This function determines the minimum volume level allowable with the VOLUME (VOL) Up/Down control. In 004 - STRT CHANNEL (Start Channel) If active, this function allows you to determine the initial this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 63 -- 0 channel number when the TV is turned On. This feature change values with ADJ Left/Right arrow. The factory I-I-I is useful for an in-house information channel, since the TV would always select that channel when it is turned On. Setting this to 255 causes the last channel viewed default is 0, which provides the full range of volume control, if item 009 MAX VOLUME is also set to 63. It may be best to set the same value on every TV. I-I-I -t c when the TV was turned Off, to be the tuned to chan- NOTE: The minimum volume level cannot have a value nel when the TV is turned On again. Note: For a digital setting higher than the MAX VOLUME level (described Start Channel, always remember to set item 104 to the below). Minor Start Channel number. 255 = Last channel 1 _ 125 = Ch X 0 = Aux 126 Map to Channel 3. 127 Map to Channel 4. 97