LG LP6000ER Owners Manual - Page 13

Caution - window air

Page 13 highlights

ENGLISH 3 Install support bracket on window. See FIG. 3. Install leveling bolt up through bottom side of support bracket. You can choose a short bolt (ITEM C) or a long one (ITEM B) according to window type. Also, you should select the position of hole on bracket. Position bracket on sill 1 inch (25.4mm) to left of center line of window (See FIG. 3). Fasten bracket loosely to sill with screws (ITEM D) provided. Adjust leveling bolt so that the air conditioner will be installed with a very slight tilt (about 1/4") downward toward the outside for proper drainage. Tighten bracket screws. OUTER WINDOW CLOSE-UP VIEW SILL OF SUPPORT BRACKET (ITEM A) SCREW (ITEM D) INNER WINDOW SILL 1"(25.4mm) CENTER LINE OF WINDOW ADJUSTMENT SLOT LEVELING BOLT (ITEM B or C) FIG. 3 4 INSTALL THE AIR CONDITIONER IN THE WINDOW • Carefully lift the air conditioner and slide it into the open window. Be careful not to hurt waist in this operation. • Use the two hand grips on top sides of unit to lift unit. • Make sure that support bracket is inserted in the pocket under base fan, and that curtain frame guide is stopped by stopper on the support bracket as shown in FIG.6. NOTE: When unit is properly centered and pushed outward to correct bracket location, you will feel unit drop securely in place on the support bracket. Hold unit firmly during this procedure. • Lower top window sash all the way down so that sash sits firmly in top channel of unit and expandable curtain frames. CAUTION During the following step, hold unit firmly until window sash is lowered to top channel behind curtain frames. Personal injury or property damage may result if unit falls from window. SCREW INNER SILL SUPPORT BRACKET ABOUT 1/4" LEVELING BOLT OUTER SILL CENTER LINE WINDOW SASH HAND GRIP FIG. 5 INDOOR OUTDOOR FIG. 4 CAUTION Failure to securely install support bracket may result in unit falling from window if window sash is raised after unit is installed. This could result in personal injury. TOP CHANNEL INDOOR SECTION CURTAIN INNER SILL INDOOR OUTDOOR SECTION STOPPER SUPPORT BRACKET POCKET SUPPORT BRACKET LEVELING BOLT OUTER SILL OUTDOOR FIG. 6 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18

ENGLISH
13
Install support bracket on window. See FIG. 3.
Install leveling bolt up through bottom side of support
bracket. You can choose a short bolt (ITEM C) or a
long one (ITEM B) according to window type. Also,
you should select the position of hole on bracket.
Position bracket on sill 1 inch (25.4mm) to left of
center line of window (See FIG. 3).
Fasten bracket loosely to sill with screws (ITEM D)
provided.
Adjust leveling bolt so that the air conditioner will be
installed with a very slight tilt (about 1/4") downward
toward the outside for proper drainage. Tighten
bracket screws.
INSTALL THE AIR CONDITIONER IN
THE WINDOW
• Carefully lift the air conditioner and slide it into the
open window. Be careful not to hurt waist in this
operation.
• Use the two hand grips on top sides of unit to lift
unit.
• Make sure that support bracket is inserted in the
pocket under base fan, and that curtain frame guide
is stopped by stopper on the support bracket as
shown in FIG.6.
NOTE:
When unit is properly centered and pushed
outward to correct bracket location, you will feel unit
drop securely in place on the support bracket. Hold
unit firmly during this procedure.
• Lower top window sash all the way down so that
sash sits firmly in top channel of unit and
expandable curtain frames.
4
3
Failure to securely install support bracket may
result in unit falling from window if window sash is
raised after unit is installed. This could result in
personal injury.
CAUTION
During the following step, hold unit firmly until
window sash is lowered to top channel behind
curtain frames. Personal injury or property damage
may result if unit falls from window.
CAUTION
SCREW
(ITEM D)
INNER
WINDOW
SILL
1"(25.4mm)
OUTER
WINDOW
SILL
CLOSE-UP VIEW
OF SUPPORT BRACKET
(ITEM A)
CLOSE-UP VIEW
OF SUPPORT BRACKET
(ITEM A)
SCREW
(ITEM D)
LEVELING BOLT
(ITEM B or C)
LEVELING BOLT
(ITEM B or C)
ADJUSTMENT SLOT
CENTER LINE
OF WINDOW
CENTER LINE
OF WINDOW
OUTDOOR
INDOOR
INNER SILL
SCREW
LEVELING
BOLT
OUTER SILL
SUPPORT
BRACKET
ABOUT 1/4"
FIG. 3
CENTER LINE
FIG. 5
OUTDOOR
INDOOR
LEVELING BOLT
SUPPORT
BRACKET
STOPPER
SUPPORT
BRACKET
POCKET
HAND GRIP
WINDOW SASH
INDOOR
SECTION
INNER SILL
OUTER SILL
OUTDOOR
SECTION
TOP CHANNEL
CURTAIN
FIG. 6
FIG. 4