LG LRSDS2706D Owners Manual - Page 14

Removing the Hinge Cover, Removing the Freezer Door

Get LG LRSDS2706D PDF manuals and user guides View all LG LRSDS2706D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

14 INSTALLATION • Tools Needed - Flat-head screwdriver - Phillips screwdriver Removing the Hinge Cover Remove the screws from the hinge cover at the top of the refrigerator. Lift the hook (not visible), located at the bottom of the front side of the cover with a flat-head screwdriver. 3 Pull out the water supply lines g. Disconnect all the wire harnesses h. Unscrew the ground wire i. Removing the Freezer Door 1 The water supply is connected to the upper right part of the rear surface of the refrigerator. Remove the clip in the joint area. Hold the water supply connection and gently push the collet a to detach the water supply line as shown. NOTE • The number of wire harnesses may vary depending on the model. • Ground wire is only present on some models. 4 Rotate the hinge lever j counterclockwise. Lift the top hinge k free of the hinge lever latch l. NOTE • Disassembling/Assembling the Water Lines b Collet c Tube d Insert line e Clip 2 Remove the screws from the water line cover f and detach the cover. CAUTION • When lifting the hinge free of the latch, be careful that the door does not fall forward. 5 Free the hinge from the water lines and wire harnesses and set it aside. 6 Lift the door from the bottom hinge pin m and place it, inside facing up, on a nonscratching surface.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
14
INSTALLATION
•
Tools Needed
- Flat-head screwdriver
- Phillips screwdriver
Removing the Hinge Cover
Remove the screws from the hinge cover at the top
of the refrigerator. Lift the hook (not visible),
located at the bottom of the front side of the cover
with a flat-head screwdriver.
Removing the Freezer Door
1
The water supply is connected to the upper
right part of the rear surface of the
refrigerator. Remove the clip in the joint area.
Hold the water supply connection and gently
push the collet
a
to detach the water supply
line as shown.
NOTE
•
Disassembling/Assembling the Water Lines
b
Collet
c
Tube
d
Insert line
e
Clip
2
Remove the screws from the water line cover
f
and detach the cover.
3
Pull out the water supply lines
g
. Disconnect
all the wire harnesses
h
. Unscrew the ground
wire
i
.
NOTE
•
The number of wire harnesses may vary
depending on the model.
•
Ground wire is only present on some models.
4
Rotate the hinge lever
j
counterclockwise.
Lift the top hinge
k
free of the hinge lever
latch
l
.
CAUTION
•
When lifting the hinge free of the latch, be
careful that the door does not fall forward.
5
Free the hinge from the water lines and wire
harnesses and set it aside.
6
Lift the door from the bottom hinge pin
m
and place it, inside facing up, on a non-
scratching surface.