Lantronix IONPS6-D ION106 User Guide Rev E - Page 36

Configuring HyperTerminal, Click Device Manager. The Device Manager window displays.

Get Lantronix IONPS6-D PDF manuals and user guides View all Lantronix IONPS6-D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Lantronix ION106-x User Guide Configuring HyperTerminal After the USB driver has been installed you must set up the terminal emulator software (e.g., HyperTerminal) to use the USB COM port. 1. On the desktop, right-click on My Computer. 2. Select Manage. The Computer Management window displays. 3. Click Device Manager. The Device Manager window displays. 4. In the right panel, expand the list for Ports (COM & LPT). Note the USB COM port number; you will need to provide this information in step 8 below. 5. Launch the HyperTerminal software. a) Click Start. b) Select All Programs > Accessories > Communications. c) Click HyperTerminal. The Connection Description window displays. 6. Type in a name and select an icon that will be used for this connection. 7. Click OK. The Connect To window displays. 8. From the drop-down list in the Connect using field, select the COM port noted in step 4. 9. Click OK. The Port Settings window displays. 10. Set the COM port properties as follows: • Bits per second: 115200 • Data bits: 8 • Parity: None • Stop bits: 1 • Flow control: None Note: the IONMM can autodetect the rate (Bits per second setting). 11. Click OK. A blank HyperTerm window displays. 12. In the HyperTerm window, select File>Properties. 13. Click the Settings tab. 14. In the Emulation field, select VT100. 15. Click ASCII Setup.... 16. Verify that Wrap lines that exceed terminal width is selected (checkbox is checked). 17. Click OK twice. 18. Login (see "Starting a USB Session" below). 33658 Rev. E https://www.lantronix.com/ 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Lantronix
ION106-x User Guide
33658 Rev. E
36
Configuring HyperTerminal
After the USB driver has been installed you must set up the terminal emulator software (e.g.,
HyperTerminal) to use the USB COM port.
1.
On the desktop, right-click on My Computer.
2.
Select Manage. The Computer Management window displays.
3.
Click Device Manager. The Device Manager window displays.
4.
In the right panel, expand the list for Ports (COM & LPT). Note the USB COM port number; you
will need to provide this information in step 8 below.
5.
Launch the HyperTerminal software.
a)
Click Start.
b)
Select All Programs > Accessories > Communications.
c)
Click HyperTerminal. The Connection Description window displays.
6.
Type in a name and select an icon that will be used for this connection.
7.
Click OK. The Connect To window displays.
8.
From the drop-down list in the Connect using field, select the COM port noted in step 4.
9.
Click OK. The Port Settings window displays.
10.
Set the COM port properties as follows:
•
Bits per second:
115200
•
Data bits:
8
•
Parity:
None
•
Stop bits:
1
•
Flow control:
None
Note: the IONMM can autodetect the rate (Bits per second setting).
11.
Click
OK
.
A blank HyperTerm window displays.
12.
In the HyperTerm window, select File>Properties.
13.
Click the Settings tab.
14.
In the Emulation field, select VT100.
15.
Click ASCII Setup
....
16.
Verify that Wrap lines that exceed terminal width is selected (checkbox is checked).
17.
Click OK twice.
18.
Login (see “Starting a USB Session” below).