Lantronix NM2-FXS-01 Installation Guide Rev D - Page 10

Pre-Installation Checklist, CAUTION, NM2-FXS-2230-SFP-01, Class I Laser Compliance

Get Lantronix NM2-FXS-01 PDF manuals and user guides View all Lantronix NM2-FXS-01 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Lantronix NM2-FXS-2230-SFP-01 Install Guide Pre-Installation Checklist Before installing your NIC, review the preceding sections, and then do the following: 1. Verify that your system is using the latest BIOS. 2. If you download the driver software, record the path where you saved the downloads. 3. If your system is active, shut it down. Do not install the NIC until system power is completely removed. When system shutdown is complete, power OFF and unplug your system. 4. Holding the NIC by the edges, remove it from its shipping package and place it on an antistatic surface. 5. Check the NIC for signs of damage, particularly on the PCB edge connector. CAUTION: Never attempt to install a damaged NIC card. If the NIC is damaged, report it to Lantronix. 6. CAUTION: Wear a grounding device and observe electrostatic discharge precautions when installing the NIC in a system. Failure to observe this caution could result in damage to the NIC. Before installing the NIC, ensure that system power is OFF, the power cord is unplugged from the power outlet, and that proper electrical grounding procedures have been followed. 7. CAUTION: Install the NIC in an operating environment where the temperature range is from 0°C to +45°C (+32°F to +113 °F), with relative humidity of 5% to 90% non-condensing. Failure to observe this caution could result in poor equipment performance. 8. CAUTION: DO NOT install the NIC in areas where strong electromagnetic fields (EMF) exist. Failure to observe this caution could result in poor equipment performance and data corruption. NM2-FXS-2230-SFP-01 9. Note: You must install the TN-SFP-GE-100FX in the open SFP slot before you power up the PC. 10. Class I Laser Compliance: This product has been tested and found to comply with the limits for FDA Class I laser for IEC60825, EN60825, and 21CFR1040 specifications. Warning: Visible and invisible laser radiation when open. DO NOT stare into laser beam or view directly with optical instruments. Failure to observe this warning could result in damage to your eyes or blindness. 33730 Rev. D https://www.lantronix.com/ Page 10 of 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
Lantronix
NM2-FXS-2230-SFP-01 Install Guide
33730 Rev. D
Page
10
of
17
Pre-Installation Checklist
Before installing your NIC, review the preceding sections, and then do the following:
1
. Verify that your system is using the latest BIOS.
2
. If you download the driver software, record the path where you saved the downloads.
3
. If your system is active, shut it down. Do not install the NIC until system power is completely removed. When system
shutdown is complete, power OFF and unplug your system.
4.
Holding the NIC by the edges, remove it from its shipping package and place it on an antistatic surface.
5.
Check the NIC for signs of damage, particularly on the PCB edge connector.
CAUTION
: Never attempt to install a
damaged NIC card. If the NIC is damaged, report it to Lantronix.
6.
CAUTION
: Wear a grounding device and observe electrostatic discharge precautions when installing the NIC in a
system. Failure to observe this caution could result in damage to the NIC. Before installing the NIC, ensure that system
power is OFF, the power cord is unplugged from the power outlet, and that proper electrical grounding procedures have
been followed.
7.
CAUTION
: Install the NIC in an operating environment where the temperature range is from 0°C to +45°C (+32°F to
+113 °F), with relative humidity of 5% to 90% non-condensing. Failure to observe this caution could result in poor
equipment performance.
8.
CAUTION
: DO NOT install the NIC in areas where strong electromagnetic fields (EMF) exist. Failure to observe this
caution could result in poor equipment performance and data corruption.
NM2-FXS-2230-SFP-01
9
.
Note
: You must install the TN-SFP-GE-100FX in the open SFP slot before you power up the PC.
10. Class I Laser Compliance
: This product has been tested and found to comply with the limits for FDA Class I laser for
IEC60825, EN60825, and 21CFR1040 specifications.
Warning
: Visible and invisible laser radiation when open. DO NOT
stare into laser beam or view directly with optical instruments. Failure to observe this warning could result in damage to
your eyes or blindness.