Lantronix SCS100/200/400 SCS100 / SCS200 / SCS400 - User Guide - Page 14

Serial Connector Pinouts, RS-232/RS-485 DB25 Connector, RS-232 DB9 Connector, PC Card Slot

Get Lantronix SCS100/200/400 PDF manuals and user guides View all Lantronix SCS100/200/400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

SCS100/200/400 User Guide 3: The SCS200 Note: The Reset button returns the SCS to its factory default configuration when you press and hold it during the power-up and boot process. Resetting to factory default will enable DHCP. Serial Connector Pinouts RS-232/RS-485 DB25 Connector The DB25 connector provides a dual RS-232/RS-485 DTE serial port. The default serial port settings are 9600 baud, 8 bits, no parity, and 1 stop bit. DB25 Serial Connector (DTE DB25 Male) RS-232 DB9 Connector The SCS200 DB9 connector provides an RS-232 DTE serial port. The default serial port settings are 9600 baud, 8 bits, no parity, and 1 stop bit. DB9 Serial Connector PC Card Slot The SCS200 PC card slot accepts Type I/II PC cards. As of this writing, the SCS200 software supports 16-bit IEEE 802.11 wireless networking PC cards, PCMCIA modem cards, and ATA flash disks and hard-drive PC cards. New cards may be added. Note: Changes in firmware releases may affect compatibility. 3-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
SCS100/200/400 User Guide
3: The SCS200
Note:
The Reset button returns the SCS to its factory default configuration when you
press and hold it during the power-up and boot process. Resetting to factory default will
enable DHCP.
Serial Connector Pinouts
RS-232/RS-485 DB25 Connector
The DB25 connector provides a dual RS-232/RS-485 DTE serial port. The default serial
port settings are 9600 baud, 8 bits, no parity, and 1 stop bit.
DB25 Serial Connector (DTE DB25 Male)
RS-232 DB9 Connector
The SCS200 DB9 connector provides an RS-232 DTE serial port. The default serial port
settings are 9600 baud, 8 bits,
no parity, and 1 stop bit.
DB9 Serial Connector
PC Card Slot
The SCS200 PC card slot accepts Type I/II PC cards.
As of this writing, the SCS200
software supports 16-bit IEEE 802.11 wireless networking PC cards, PCMCIA modem
cards, and ATA flash disks and hard-drive PC cards. New cards may be added.
Note:
Changes in firmware releases may affect compatibility.
3-2