Lantronix SCS100/200/400 SCS100 / SCS200 / SCS400 - User Guide - Page 18

DB9 Serial Connector Pinouts, PC Card Slots, Power Connectors, Power Jack

Get Lantronix SCS100/200/400 PDF manuals and user guides View all Lantronix SCS100/200/400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

SCS100/200/400 User Guide 4: The SCS400 Note: The Reset button returns the SCS to its factory default configuration when you press and hold it during the power-up and boot process. Resetting to factory default will enable DHCP. DB9 Serial Connector Pinouts The following figure shows the pin connections of the SCS400 DB9 RS-232 connector. . The default serial port settings are 9600 baud, 8 bits, no parity, and 1 stop bit. DB9 RS-232 Serial Connector PC Card Slots PC Card Slot The SCS400 PC card slot accepts Type I/II PC cards. As of this writing, the SCS400 software supports 16-bit IEEE 802.11 wireless networking PC cards, PCMCIA modem cards, and ATA flash disks and hard-drive PC cards. New cards may be added. Note: Changes in firmware releases may affect compatibility. Power Connectors Power is supplied to the SCS400 using one of the connectors described below. Power Jack The SCS400 ships with a standard barrel power jack whose inner conductor is positive. Power Jack Connector 2.1 mm 5.5 mm - + 4-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
SCS100/200/400 User Guide
4: The SCS400
Note:
The Reset button return
you press and hold it during th
s the SCS to its factory default configuration when
e power-up and boot process. Resetting to factory
DB9 Serial Connector Pinouts
The following figure shows the pin connections of the SCS400 DB9 RS-232 connector. .
The default serial port settings are 9600 baud, 8 bits, no parity, and 1 stop bit.
DB9 RS-232 Serial Connector
default will enable DHCP.
PC Card Sl
networking PC cards, PCMCIA modem
A flash disks and hard-drive PC cards. New cards may be added.
Power Con
Power Jack
The SCS400 ships with a standard barrel power jack whose inner conductor is positive.
Power Jack Connector
ots
PC Card Slot
The SCS400 PC card slot accepts Type I/II PC cards.
As of this writing, the SCS400
software supports 16-bit IEEE 802.11 wireless
cards, and AT
Note:
Changes in firmware releases may affect compatibility.
nectors
Power is supplied to the SCS400 using
one
of the connectors described below.
+
-
2.1 mm
5.5 mm
4-2