Lantronix SCS100/200/400 SCS100 / SCS200 / SCS400 - User Guide - Page 54

Set Server RARP {Enabled, Disabled

Get Lantronix SCS100/200/400 PDF manuals and user guides View all Lantronix SCS100/200/400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

SCS100/200/400 User Guide 7: Troubleshooting Init 451 Reboots the SCS after it has been configured. If the SCS can find and load the specified software loadfile, it restarts itself with full functionality. If the loadfile is not found, the SCS attempts to reload continuously. If there is an error, or if the console's Enter key is pressed, the SCS re-enters the Boot Configuration Program. Set Server BOOTP {Enabled, Disabled} Enables or disables the sending of BOOTP queries during the boot sequence. It is enabled by default. Set Server Bootgateway ip_address Specifies the address of a router so TFTP upgrades can be performed over a routed network. This requires Boot version 1.3 or higher. TFTP (UDP port 69) must not be blocked on the routers. Set Server Hardware xx-xx-xx Specifies the last three numbers of the SCS's Ethernet address. The first three numbers are supplied automatically. The Ethernet address should have been set at the factory. Setting an incorrect address could cause serious network problems. Set Server IPAddress ip_address Specifies this SCS's IP address. Uses the standard numeric format. Set Server Loadhost ip_address Specifies the host to attempt to load the file from. The IP address should be in standard numeric format (no text names are allowed). Set Server RARP {Enabled, Disabled} Enables or disables the sending of RARP queries during the boot sequence. It is enabled by default. Set Server Secondary ip_address Specifies a backup loadhost. The IP address should be in standard numeric format (no text names are allowed). The backup loadhost is queried if the primary host cannot load the server. Set Server Software filename Specifies the name of the file to load. The SCS automatically adds .SYS to the filename you specify. Note that all protocols must have a filename specified (either the default or set by the user). For more information, see Updating Software. TCP/IP users must use the Software option to specify the loadhost, the loadfile, and their own network address. TFTP users can specify a complete path name (up to 31 characters) if the file is located in a directory other than the default. The case of the filename must match that of the filename loaded onto the host computer. 7-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
SCS100/200/400 User Guide
7: Troubleshooting
Init 451
Reboots the SCS after it has been configured. If the SCS can find and load the specified
software loadfile, it restarts itself with full functionality. If the loadfile is not found, the SCS
attempts to reload continuously. If there is an error, or if the console's
Enter
key is
pressed, the SCS re-enters the Boot Configuration Program.
Set Server BOOTP {Enabled, Disabled}
Enables or disables the sending of BOOTP queries during the boot sequence. It is
enabled by default.
Set Server Bootgateway
ip_address
Specifies the address of a router so TFTP upgrades can be performed over a routed
network. This requires Boot version 1.3 or higher. TFTP (UDP port 69) must not be
blocked on the routers.
Set Server Hardware
xx-xx-xx
Specifies the last three numbers of the SCS's Ethernet address. The first three numbers
are supplied automatically.
The Ethernet address should have been set at the factory. Setting an incorrect address
could cause serious network problems.
Set Server IPAddress
ip_address
Specifies this SCS's IP address. Uses the standard numeric format.
Set Server Loadhost
ip_address
Specifies the host to attempt to load the file from. The IP address should be in standard
numeric format (no text names are allowed).
Set Server RARP {Enabled, Disabled}
Enables or disables the sending of RARP queries during the boot sequence. It is enabled
by default.
Set Server Secondary
ip_address
Specifies a backup loadhost. The IP address should be in standard numeric format (no
text names are allowed). The backup loadhost is queried if the primary host cannot load
the server.
Set Server Software
filename
Specifies the name of the file to load. The SCS automatically adds
.SYS
to the filename
you specify. Note that all protocols must have a filename specified (either the default or
set by the user). For more information, see
Updating Software
.
TCP/IP users must use
the Software option to specify the loadhost, the loadfile, and their own network address.
TFTP users can specify a complete path name (up to 31 characters) if the file is located
in a directory other than the default. The case of the filename must match that of the
filename loaded onto the host computer.
7-5