Lantronix UDS2100 UDS2100 - User Guide

Lantronix UDS2100 Manual

Get Lantronix UDS2100 PDF manuals and user guides View all Lantronix UDS2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Lantronix UDS2100 manual content summary:

  • Lantronix UDS2100 | UDS2100 - User Guide - Page 1
    UDS2100 User Guide Part Number 900-448 Revision D January 2009
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 2
    8/08 1/09 Rev. Comments A Initial document B Updated to reflect firmware v. 6.5, including UDP Broadcast; added two more Monitor Mode commands and diagrams of mounting brackets. C Updated for firmware v6.6 D Reference to documentation on Lantronix website; minor corrections UDS2100 User Guide 2
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 3
    1 and Channel 2 Configuration 27 Serial Settings 27 Connection Settings - TCP 30 Connection Settings - UDP 33 Apply Settings 35 Apply Factory Defaults 35 5: Configuration via Telnet or Serial Port (Setup Mode) 36 Accessing Setup Mode 36 Telnet Connection 36 UDS2100 User Guide 3
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 4
    Port Connection 37 Exiting Setup Mode 38 6: Setup Mode: Server Configuration 39 Server Configuration (Option 0 39 IP Address 39 Set Gateway IP Address 39 Netmask: Number of Bits for Host Part 40 Set DNS Server IP Address 40 Change Telnet Configuration Password 40 DHCP Name 41 7: Setup
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 5
    Contents SNMP Community Name 58 Disable Telnet Setup 58 Disable TFTP Firmware Update 58 Disable Port 77FE (Hex 59 Disable Web Server 59 Disable Web Setup 59 Disable ECHO Ports 59 Enable Enhanced Password 59 Default Settings (Option 7 59 Channel 1 and Channel 2 Configuration Defaults 60
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 6
    MAC Address 37 Figure 5-2. Setup Menu Options 37 Figure 6-1. Network Settings 39 Figure 7-1. Serial Port Settings 42 Figure 7-3. Manual Connection Address Example 47 Figure 8-1. Expert Settings 56 Figure 8-2. Security Settings 58 Figure 9-1. TFTP Window 62 Figure 11-1. Diagnostic, Power, and
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 7
    Details the serial port settings. 8: Setup Mode: Advanced Settings Details expert and security settings and explains how to reset the unit to factory default values. 9: Firmware Upgrades Provides instructions for obtaining the latest firmware and updating the UDS. 10: Monitor Mode
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 8
    and Online Help Provides instructions for using the Windows-based utility to configure the UDS2100 and other Lantronix device servers. Explain and demonstrate assigning an IP address to the UDS and setting up the UDS and Com Port Redirector. See http://ts.lantronix.com/tutorials.html. Provides
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 9
    2: Introduction The UDS2100 is a 2-port device server that provides a quick, simple, and costeffective way to bring the advantages of data accessibility and remote management to devices not currently connected to a network. Applications The UDS family of Device Servers allows serial devices, such as
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 10
    connections. Figure 2-2. Direct TCP/IP or Redirector Configuration Note: For step-by-step instructions on configuring the UDS for serial tunneling or for use with the Com Port Redirector, see UDS Configuration Tutorials on the Lantronix web site: www.lantronix.com/support. UDS2100 User Guide 10
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 11
    connection arrives correctly at the target. Supported protocols include: ARP, UDP, TCP, ICMP, Telnet, TFTP, AutoIP, DHCP, HTTP, and SNMP for network communications. TCP, UDP, and Telnet for connections to the serial port. TFTP for firmware updates. IP for addressing, routing, and data block handling
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 12
    address) The first three bytes of the hardware address are fixed and read 00-20-4A, identifying the unit as a Lantronix product. The fourth, fifth, and sixth bytes are unique numbers assigned to each unit. Figure 2-3. Sample Hardware Address 00-20-4A-14-01-18 or 00:20:4A:14:01:18 UDS2100 User Guide
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 13
    using the following list. If any item is missing or damaged, contact your place of purchase immediately. UDS2100 DB9F to DB9F Null Modem Cable (P/N 500-164) Power supply CD with UDS2100 User Guide and utilities (DeviceInstaller and Com Port Redirector) Quick Start Guide UDS2100 User Guide 13
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 14
    your unit using the power supply that was included in the packaging. Note: The required input voltage is 9-30 VDC (center +) (1.8W maximum power). 4. Supply power to the serial device. Note: If you encounter a problem, please see 11: Troubleshooting and Contact Information. UDS2100 User Guide 14
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 15
    about using the DeviceInstaller (graphical user interface) and serial port login (command line interface) methods. Note: For information about other methods of assigning the IP address, such as DHCP, AutoIP, ARP, and Telnet, see B: Alternative Ways to Assign an IP Address. UDS2100 User Guide 15
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 16
    can work correctly on a network. The unit's IP address is normally set to 0.0.0.0 at the factory. The hardware address is on the product label. The unit is DHCP enabled as the default. To assign an IP address manually: 1. Click Start Programs Lantronix DeviceInstaller DeviceInstaller. If your PC has
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 17
    1. Click Start Programs Lantronix DeviceInstaller DeviceInstaller. 2. Click the UDS folder. The list of available Lantronix UDS2100 devices displays. 3. Expand the list of UDS2100s by clicking the + symbol next to the UDS2100 icon. Select the UDS2100 unit by clicking on its IP address to view its
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 18
    the UDS2100's device family as UDS. Type Displays the device type as UDS2100. ID Displays the UDS2100's ID embedded within the box. Hardware Address Displays the UDS2100's hardware (or MAC) address. Firmware Version Displays the firmware currently installed on the UDS2100. Extended Firmware
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 19
    configurable field. Displays True. UDS2100 supports a baud rate of 921600. Supports HTTP Server Non-configurable field. Displays True. Supports HTTP Setup Non-configurable field. Displays True. Supports 230K Baud Rate Non-configurable field. Displays True. UDS2100 supports a baud rate of 230400
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 20
    until you get to IP address. 4. Enter the new IP address, subnet mask, and gateway (if applicable). 5. Do one of the following: Continue with 5: Configuration via Telnet or Serial Port (Setup Mode). Select 9 to save and exit Setup Mode. The unit performs a power reset. UDS2100 User Guide 20
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 21
    pane. . The list of Lantronix device servers displays in the left 3. Click the UDS folder. The list of available UDS products displays. 4. Expand the list of UDS2100s by clicking the + symbol next to the UDS2100 icon. 5. Select the UDS2100 unit by clicking its hardware address. 6. In the right
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 22
    4-1. Lantronix Web Manager The main menu is in the left pane of the Web Manager window. Network Configuration The unit's network values display when you select Network from the main menu. The following sections describe the configurable parameters on the Network Settings page. UDS2100 User Guide
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 23
    ): BOOTP Select Enable to permit the Bootstrap Protocol (BOOTP) server to assign the IP address from a pool of addresses automatically. Enable is the default. DHCP Select Enable to permit the Dynamic Host Configuration Protocol (DHCP) to assign a leased IP address to the UDS2100 User Guide 23
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 24
    machine to be resolved automatically. Enter the IP address of the DNS server. If the device is DHCP enabled, the DHCP server provides the DNS server IP address, which will override this configured value. Note: This setting is applicable only in Manual Connection mode. 4. When you are finished
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 25
    Server from the main menu. The following sections describe the configurable parameters on the Server Settings page. Figure 4-3. Server Settings To configure the UDS2100's device server settings: 1. On the main menu, click Server. 2. Configure or modify the following fields: UDS2100 User Guide
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 26
    entry contains an IP address and a port number. Note: The host list is disabled for Manual and Modem Mode. The unit does not accept a data connection from a remote device when the hostlist option is enabled. To configure the host list: 1. On the main menu, click Hostlist. UDS2100 User Guide 26
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 27
    setting is 3. Enter the duration (in seconds) the UDS2100 should abandon attempting a connection to the host list. The default setting is 250. Host Information Host Address Enter or modify the host's IP address. Port Enter the target port number. 3. When you are finished, click the OK button
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 28
    In the available fields, enter the following information: Channel 1 Disable Serial Port When selected, disables communication through the serial port. The serial port is enabled by default. Note: This feature is not available on single port device servers, since it can only be applied to channel
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 29
    The default setting is 1. Select to enable packing on the UDS2100. Two firmware-selectable device. The default setting is No. At Time of Disconnect Select Yes to clear the input buffer when the network connection to or from the device is disconnected. The default setting is No. UDS2100 User Guide
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 30
    The default setting is No. 3. When you are finished, click the OK button. 4. On the main menu, click Apply Settings. Connection Settings - TCP To configure a channel's TCP settings: 1. On the main menu, click Connection. The Connection Settings window for the channel displays. UDS2100 User Guide
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 31
    for Telnet mode. The default setting is No. Password If Password Required was set to Yes, enter the password for passive connections. Modem Escape Sequence Disable or enable the unit's ability to send the escape Pass Through sequence. The default is Y (Yes) (send the escape UDS2100 User Guide
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 32
    range is reached. Disabled by default. Enter the remote port number. Enter the IP address of the remote device. Available for configuration only when Active Connect is set to None. Select Enable to permit Telnet communication to the UDS unit. The Telnet Com Port Cntrl feature is used in conjunction
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 33
    connection when Ctrl+D or Hex 04 is detected. Both Telnet Com Port Cntrl and Check EOT (Ctrl+ D) must be enabled for Disconnect with EOT to function properly. Ctrl+D is only detected going from the serial port to the network. The default setting is No. Inactivity Timeout Use this parameter to set
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 34
    default is not to broadcast. Note: Datagrams are sent as subnet-directed broadcasts. Device Address Table The table is enabled when Datagram Type is set to FD. Enter values between 1 and 255 to identify units on the local network of device servers. Note: Lantronix Tech Support supports Datagram
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 35
    makes the changes permanent and reboots the UDS2100. Apply Factory Defaults 1. Click the Apply Defaults button to set the device server back to the default settings. For details see Default Settings on page 59. 2. Click Yes to set factory settings, or click No to cancel. UDS2100 User Guide 35
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 36
    Setup Mode Telnet Connection To configure the unit over the network, establish a Telnet connection to port 9999. Note: You can also use DeviceInstaller to access Telnet. Select the device from the main window list, and click the Telnet Configuration tab. Skip steps 1 and 2. UDS2100 User Guide
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 37
    serial port. The default serial port settings are 9600 baud, 8 bits, no parity, 1-stop bit, no-flow control. Note: The UDS always uses the above serial settings at bootup. 2. Reset the UDS2100 unit by cycling the unit's power (turning the power off and back on). Immediately upon resetting the device
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 38
    5: Configuration via Telnet or Serial Port (Setup Mode) Exiting Setup Mode To exit setup mode: You have two options: To save all changes and reboot the device, select option 9 Save and exit from the Change Setup menu. All values are stored in nonvolatile memory. To exit the configuration mode
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 39
    display when you select Server configuration (option 0). The IP Address, Set Gateway IP Address, and Netmask fields display the current values. Figure 6-1. Network Settings IP Address If DHCP is not used to assign IP addresses, enter the IP address manually. The IP address must be set to
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 40
    DNS server IP address, which will override this configured value. Note: This setting is applicable only in Manual Connection mode. Change Telnet Configuration Password Setting the Telnet configuration password prevents unauthorized access to the setup menu through a Telnet connection to port 9999
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 41
    unit). For example, if the MAC address is 00-20-4A-12-3456, then the default DHCP name is C123456. Custom DHCP Name: You can create your own DHCP name. If you are using an IP address of 0.0.0.0, then the last option in Server configuration is Change DHCP device name. This option allows you to change
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 42
    Setup menu to define how the serial port device, such as a modem, must agree on a speed or baud rate to use for the serial connection. Valid baud rates are 300, 600, 1200, 2400, 4800, 9600 (default), 19200, 38400, 57600, 115200, 230400, 460800, and 921600 baud. Baudrate (9600) ? _ UDS2100 User Guide
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 43
    Setup Mode: Channel Configuration I/F (Interface) Mode The Interface (I/F) Mode is a bit-coded byte entered in hexadecimal notation. The default by the software. This might default setting is 00. Flow (00) ? _ Use the following table to select flow control options: UDS2100 User Guide 43
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 44
    Port No (10001) ? _ The default setting for Port 1 is 10001. The range is 1-65535, except for the following reserved port numbers: Table 7-4. Reserved Port Numbers Port Numbers Reserved for 1 - 1024 Reserved (well known ports) 9999 Telnet setup hexadecimal notation. The default setting is C0.
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 45
    7: Setup Mode: Channel Configuration Table 7-5. Connect Mode Options Connect Mode Option 7 With active Modem Control In 0 0 1 0 With a specific start character 0 0 1 1 Manual connection 0 1 0 0 Autostart 0 1 0 1 Hostlist 0 0 1 0 d) Datagram Type Default setting. UDS2100 User Guide 45
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 46
    bytes of the IP address. If the IP address entered is 0.0.0.0/0, the device server enters Monitor Mode. For example, if the remote IP address already configured in the unit is 129.1.2.3, then an example command string would be C3/7. (This would connect to 129.1.2.3 and port 7.) You may also
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 47
    . Hostlist supports a minimum of 1 and a maximum of 12 entries. Each entry contains the IP address and the port number. The hostlist is disabled for Manual and Modem Modes. The unit does not accept a data connection from a remote device when the hostlist option is enabled. UDS2100 User Guide 47
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 48
    IP address of 0.0.0.0, that entry and all others after it are deleted. 3. After completing the hostlist, repeat the previous step if necessary to edit the hostlist again. 4. For Retrycounter, enter the number of times the Lantronix option. The default is not to broadcast. UDS2100 User Guide 48
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 49
    Table 4-11. Modem Mode Messages Meaning OK Command was executed without error. CONNECT A network connection has been established. NO CARRIER A network connection has been closed. UDS2100 User Guide 49
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 50
    7: Setup Mode: Channel Configuration Message RING n.n.n.n. Meaning A remote device, having IP address n.n.n.n, is connecting to this device. Numeric Response 0 OK 1 pppp or Makes a connection to an IP address (x.x.x.x) and a remote port ATDTx.x.x.x/pppp number (pppp). or UDS2100 User Guide 50
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 51
    the escape sequence. The default setting is Y (Yes) (send the escape sequence). Show IP addr after 'RING' Show IP addr after 'RING' (Y) ? _ Disable or enable the UDS's ability to show the IP address after RING in Modem Mode. The default is Y (Yes), to show the IP address. UDS2100 User Guide 51
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 52
    value. Table 7-7. Disconnect Mode Options Disconnect Mode Option 7 6 5 4 3 2 1 0 Disconnect when Modem Control In is not asserted (6) 1 Ignore Modem Control In Telnet Com Port Cntrl and terminal type setup (1) 0 1 Channel (port) password (2) 1 Hard disconnect (3) 0 UDS2100 User Guide 52
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 53
    Telnet Com Port Control feature is used in conjunction with Com Port Redirector. The UDS sends the "Terminal Type" upon an outgoing connection. (2) A password is required for a connection to the serial port to the device 1 Clear when the network connection to or from the device is disconnected
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 54
    7: Setup Mode: Channel Configuration packet count low. The alternate packing algorithm minimizes the packet count on the network found. If this option is set, the unit sends immediately after recognizing the transmit condition (sendchar or timeout). The default setting is 0. UDS2100 User Guide 54
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 55
    Setup the terminal name for the Telnet terminal type. Enter only one Port) Password This parameter appears only if the channel (port) password option is enabled in Disconnect Mode. With this option enabled, you can set a password on the serial port. There is no default password. UDS2100 User Guide
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 56
    timeout in s (1s - 65s; 0s=disable): (600)? _ CPU Performance Select the UDS2100's performance mode. Higher performance settings require more energy. Low is 26 Mhz; Regular is 48 Mhz; High is 88 Mhz. The default is Regular. CPU performance (0=Regular, 1=Low, 2=High): (0) UDS2100 User Guide 56
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 57
    serial setup to prevent eavesdropping. Caution: Disabling both Telnet Setup and Port 77FE will prevent users from accessing the setup menu from the network. Disabling Port 77FE also disables the Web Manager from configuring the device. Select 7 to configure security settings. UDS2100 User Guide 57
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 58
    the web pages and the serial port of the unit. Disable Telnet Setup (N) ? _ Disable TFTP Firmware Update This setting defaults to the N (No) option. The Y (Yes) option disables the use of TFTP to perform network firmware upgrades. With this option, you can download firmware upgrades over the serial
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 59
    password of 16-characters for protecting Telnet and Web Page access. Enable Enhanced Password (N) ? _ Default Settings (Option 7) Select 7 to reset the unit's Channel 1 configuration and expert settings to the default settings. The server configuration settings for IP address, gateway IP address
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 60
    OEM use only) 0 (auto-negotiate) Security Settings Defaults Disable SNMP SNMP community name Disable Telnet setup Disable TFTP Firmware Update Disable Port 77FEh Disable Web Server Disable Web Setup Disable ECHO ports Enable Enhanced Password No public No No No No No Yes No UDS2100 User Guide 60
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 61
    the .ROM (binary) version of the unit's internal operational code. 2. In the TFTP server field, enter the IP address of the unit being upgraded. 3. Select Upload operation and Binary format. 4. Enter the full path of the firmware file in the Local file name field. 5. In the Remote file name field
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 62
    menu, select Advanced/Recover Firmware. The Serial Port Firmware Upgrade window displays. 4. For Port on PC, enter the COM port on the PC that is connected to the serial port of the Lantronix unit. 5. For Device Model, be sure the appropriate device (e.g., UDS2100) displays. UDS2100 User Guide 62
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 63
    firmware file resides. Note: Make sure the UDS2100 on which you are recovering firmware is connected to this selected port on your PC. 7. Click OK to download the file. 8. When prompted, reset the device information, see Recovering Firmware in the DeviceInstaller online Help. UDS2100 User Guide 63
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 64
    .xxx.xxx). If you enter the IP address, the command is applied to another unit with that IP address. If you do not enter the IP address, the command is executed locally. Note: All commands must be in capital letters. Responses to some of the commands are in Intel Hex format. UDS2100 User Guide 64
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 65
    Network Connection Shows the unit's current IP address, gateway, subnet mask, and DNS server. Reset Resets the unit's power. Quit Exits diagnostics mode. Get configuration from memory page Gets a memory page of configuration information from the device. Set configuration to memory page Sets
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 66
    Mode Command Command Name Function The UDS stores the setup and performs a reset. It sends an X before the reset if the command was OK. Note error 1> No answer from remote device 2> Cannot reach remote device or no answer 8> Wrong parameter(s) 9> Invalid command UDS2100 User Guide 66
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 67
    . Make sure that your unit's IP address is unique. When troubleshooting the following problems, make sure that the UDS2100 is powered up. Confirm that you are using a good network connection. LEDs The following LEDs are on the top of the UDS2100: Power / Diagnostic (Blue) RX Serial 1 Activity LED
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 68
    Troubleshooting and Contact Information Figure 11-1. Diagnostic, Power, and Serial Port LEDs LEDs Table 11-1. UDS2100 LEDs Meaning Steady On = Power OK Power/Diagnostic (Blue) Blinking 2x = No DHCP response Blinking 2x = Setup Blinking Green = Full Duplex data activity UDS2100 User Guide 68
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 69
    to press Enter before the connection is closed. Telnet to port 9999 again, but press Enter as soon as you see the "Press Enter to go into Setup Mode" message. When you Telnet to port 1 to assign an IP address to the device server, the Telnet window does not respond for a long time. You may
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 70
    is the IP of the device server). If you get a response, then there is a duplicate IP address on the network. If you do not get a response, use the serial port to verify that Telnet is not disabled. With DeviceInstaller, you get the "Wrong Password" error when you try to upgrade the firmware. The
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 71
    .com Firmware downloads, FAQs, and the most up-to-date documentation are available at www.lantronix.com/support. When you report a problem, please provide the following information: Your name, and your company name, address, and phone number  Lantronix model number Lantronix MAC number Software
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 72
    Serial Ports Serial Connector Pinouts The two Male DB9 DTE connectors provide an RS-232C/RS-422 (4-wire)/ RS-485 (2-wire) interface. The default serial port settings are 9600 baud, 8 bits, no parity, 1 stop bit, no flow control. Figure 12-2. DB9 Male RS232 Serial DTE Connector UDS2100 User Guide
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 73
    and Pinouts Network Port The unit's back panel contains a 9-30VDC power plug and an RJ45 (10/100) Ethernet port. Figure 12-3. Network Interface RJ45 Ethernet Port Reset Button Power Plug Reset Button You can reset the unit to factory defaults, including clearing the network settings (IP address
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 74
    , 40% to 60% recommended Storage 10% to 90% non-condensing Case Metal enclosure with integrated wall mounts Optional 35 mm Din Rail mount available Protocols Supported ARP, UDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, and HTTP UDS2100 User Guide 74
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 75
    web server SNMP (read only) Serial login Telnet login DeviceInstaller software DeviceInstaller, Windows® 95/98/ME/NT/2000/XP-based configuration software Com Port Redirector, Windows® 98/NT/2000/XP-based virtual com port software Power 10/100 Mb Link on RJ45 10/100 Activity on RJ45 Diagnostic RX
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 76
    13: Technical Specifications Category Agency Approvals Description transient over voltages Ethernet Port: 1500 VAC isolation shielded with shield connected to chassis ground for signal integrity and ESD protection UL, CSA, FCC, CE, TUV, CTick, VCCI UDS2100 User Guide 76
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 77
    A: Mounting Brackets The following drawings provide dimensions of the brackets for mounting the UDS2100. UDS2100 User Guide 77
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 78
    DeviceInstaller, Web Manager, and Setup Mode (through a Telnet or serial connection). This section covers other methods for assigning an IP address over the network. DHCP The unit ships with a default IP address of 0.0.0.0, which automatically enables DHCP. If a DHCP server exists on the network, it
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 79
    wait longer than five seconds, the unit reboots. telnet 191.12.3.77 9999 Note: The IP address you just set is temporary and reverts to the default value when the unit's power is reset, unless you configure the unit with a static IP address and store the changes permanently. UDS2100 User Guide 79
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 80
    . Decimal 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Binary 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Hex 0 1 2 3 4 5 6 7 8 9 A B C D E F UDS2100 User Guide 80
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 81
    systems. For example: 1. On the Windows' Start menu, click Programs Accessories Calculator. 2. On the View menu, select Scientific. The scientific calculator displays. 3. Select Bin (Binary), and type the number to convert. 4. Click Hex. The hexadecimal value displays. UDS2100 User Guide 81
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 82
    D: Warranty For details on the Lantronix warranty replacement policy, please go to our Web site at www.lantronix.com/support/warranty/index.html. UDS2100 User Guide 82
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 83
    Disclaimer Manufacturer's Name & Address Lantronix 15353 Barranca Parkway, Irvine, CA 92618 USA Declares that the following product: Product Name Model: UDS2100 Device Server Conforms to the following -4-5: 1995 IEC 61000-4-6: 1996 IEC 61000-4-8: 1993 IEC 61000-4-11: 1994 UDS2100 User Guide 83
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 84
    (Cd) Chromium biphenyls (PBB) ethers (PBDE) (Cr (VI)) UDS1100 and 2100 0 0 0 0 0 0 EDS 0 0 0 0 0 0 MSS100 installed and used in accordance with this guide device not explicitly approved by Lantronix will void the user's authority to operate this device. The information in this guide
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 85
    , 61 Flow, 43 UDS2100 User Guide Flush Mode, 53 Gateway, 39 Getting started, 13 Hardware address, 12, 15 Host list settings Setup Mode, 47 Web-Manager, 26 Installation, 14 Interface Mode, 43 Internal web server, 11 IP address assigning, 16 automatic assignment, 23 factory default, 15 gateway, 39
  • Lantronix UDS2100 | UDS2100 - User Guide - Page 86
    Setup Mode, 36 accessing by serial port, 37 accessing by Telnet, 36 SNMP, 58 Source port auto-increment, 52 TCP settings, 30 Technical specifications Technical Support, 71 Telnet terminal type, 55 TFTP, 61 Troubleshooting, 7, 14, 67 UDP settings, 33 Warranty, 82 Web-Manager, 21 UDS2100 User Guide
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Part Number 900-448
Revision D
January 2009
UDS2100
User Guide