Lenovo B750 IdeaCentre B750 Hardware Maintenance Manual - Page 53

Replacing the CPU

Get Lenovo B750 PDF manuals and user guides View all Lenovo B750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Step 10. Remove the eight screws that secure the heat-sink to the motherboard, and then lift up the heat-sink to remove it. Step 11. To install the new heat-sink: a. Line up the new heat-sink with mounting holes on motherboard and secure it with the eight screws. Step 12. Reattach the system fans, EMI cover, middle cover, optical drive, computer stand and the rear cover. Replacing the CPU Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. To replace the CPU Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Unplug all power cords from electrical outlets. Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to "Left and right view" and "Rear view" for help with locating the various connectors. Step 4. Remove the rear cover. Refer to "Removing the rear cover". Step 5. Remove the computer stand. Refer to "Removing the computer stand". Step 6. Remove the optical drive. Refer to "Replacing the optical drive". Step 7. Remove the middle cover. Refer to "Removing the middle cover". Step 8. Remove the EMI cover. Refer to "Removing the EMI cover". Step 9. Remove the system fans. Refer to "Replacing the system fans". Step 10. Remove the heat-sink. Refer to "Replacing the heat-sink". Step 11. Lift the small handle and open the retainer. 1 2 Attention: Do not touch the gold contacts on the bottom of the microprocessor. When handing the microprocessor, touch only the sides. Chapter 8. Replacing hardware 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
Step 10. Remove the eight screws that secure the heat-sink to the motherboard, and then lift up the
heat-sink to remove it.
Step 11. To install the new heat-sink:
a.
Line up the new heat-sink with mounting holes on motherboard and secure it with the eight
screws.
Step 12. Reattach the system fans, EMI cover, middle cover, optical drive, computer stand and the rear
cover.
Replacing the CPU
Note:
Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.
To replace the CPU
Step 1.
Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating
system, and turn off the computer and all attached devices.
Step 2.
Unplug all power cords from electrical outlets.
Step 3.
Disconnect all cables attached to the computer. This includes power cords, input/output (I/O)
cables, and any other cables that are connected to the computer. Refer to “Left and right view”
and “Rear view” for help with locating the various connectors.
Step 4.
Remove the rear cover. Refer to “Removing the rear cover”.
Step 5.
Remove the computer stand. Refer to “Removing the computer stand”.
Step 6.
Remove the optical drive. Refer to “Replacing the optical drive”.
Step 7.
Remove the middle cover. Refer to “Removing the middle cover”.
Step 8.
Remove the EMI cover. Refer to “Removing the EMI cover”.
Step 9.
Remove the system fans. Refer to “Replacing the system fans”.
Step 10. Remove the heat-sink. Refer to “Replacing the heat-sink”.
Step 11. Lift the small handle and open the retainer.
1
2
Attention:
Do not touch the gold contacts on the bottom of the microprocessor. When handing the
microprocessor, touch only the sides.
Chapter 8
.
Replacing hardware
47