Lenovo NetVista Hardware Maintenance Manual for NetVista 2289 and 6824 systems - Page 104

Automatic Power-On features, Serial Port A Ring Detect

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

2. Select Power Management from the Configuration/Setup Utility program menu. 3. Select APM BIOS Mode within the APM sub menu and be sure it is set to Enabled. If it is not, press Left Arrow (}) or Right Arrow (Æ) to change the setting. 4. Select Automatic Hardware Power Management. 5. Set Automatic Hardware Power Management to Enabled. 6. Select values for the three categories of power management (system power, processor speed, and display), as necessary. 7. Set Hard Disk to Enabled or Disabled. Note: This does not apply to SCSI drives. 8. Press Esc twice to return to the Configuration/Setup Utility program menu. 9. Before you exit from the program, select Save Settings from the Configuration/Setup Utility program menu. 10. To exit from the Configuration/Setup Utility program, press Esc and follow the instructions on the screen. Automatic Power-On features The Automatic Power-On features within the Power Management menu allow you to enable and disable features that turn on the computer automatically. v Serial Port A Ring Detect: With this feature set to Enabled and an external modem connected to serial port (COM1), the computer will turn on automatically when a ring is detected on the modem. v PCI Modem Ring Detect: With this feature set to Enabled , the computer will turn on automatically when a ring is detected on the internal modem. v PCI Wake Up: This feature allow PCI cards that support this capability to wake the system. v Wake Up on Alarm: You can specify a date and time at which the computer will be turned on automatically. This can be either a single event or a daily event. v Wake on LAN: If the computer has a properly configured token-ring or Ethernet LAN adapter card that is Wake on LAN-enabled and there is remote network management software, you can use the IBM-developed Wake on LAN feature. When you set Wake on LAN to Enabled, the computer will turn on when it receives a specific signal from another computer on the local area network (LAN). 98 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
2.
Select
Power Management
from the Configuration/Setup Utility program
menu.
3.
Select
APM BIOS Mode
within the APM sub menu and be sure it is set to
Enabled
. If it is not, press Left Arrow (
}
) or Right Arrow (Æ) to change the
setting.
4.
Select
Automatic Hardware Power Management
.
5.
Set
Automatic Hardware Power Management
to
Enabled
.
6.
Select values for the three categories of power management (system power,
processor speed, and display), as necessary.
7.
Set
Hard Disk
to
Enabled
or
Disabled
.
Note:
This does not apply to SCSI drives.
8.
Press
Esc
twice to return to the Configuration/Setup Utility program menu.
9.
Before you exit from the program, select
Save Settings
from the
Configuration/Setup Utility program menu.
10.
To exit from the Configuration/Setup Utility program, press
Esc
and follow
the instructions on the screen.
Automatic Power-On features
The Automatic Power-On features within the Power Management menu allow you
to enable and disable features that turn on the computer automatically.
v
Serial Port A Ring Detect
: With this feature set to
Enabled
and an external
modem connected to serial port (COM1), the computer will turn on
automatically when a ring is detected on the modem.
v
PCI Modem Ring Detect
: With this feature set to
Enabled
, the computer will
turn on automatically when a ring is detected on the internal modem.
v
PCI Wake Up:
This feature allow PCI cards that support this capability to wake
the system.
v
Wake Up on Alarm
: You can specify a date and time at which the computer will
be turned on automatically. This can be either a single event or a daily event.
v
Wake on LAN
: If the computer has a properly configured token-ring or Ethernet
LAN adapter card that is Wake on LAN-enabled and there is remote network
management software, you can use the IBM-developed Wake on LAN feature.
When you set Wake on LAN to
Enabled
, the computer will turn on when it
receives a specific signal from another computer on the local area network
(LAN).
98
Hardware Maintenance Manual