Lenovo NetVista Hardware Maintenance Manual for NetVista 2289 and 6824 systems - Page 37

Connecting the first IDE CD-ROM drive or DVD-ROM drive

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

6. Install the drive into the bay. Align the screw holes and install two screws to secure the drive. 7. Each integrated drive electronics (IDE) drive requires two cables; a four-wire power cable that connects to the power supply and a signal cable that connects to the system board. For a CD-ROM drive, you might also have an audio cable. The steps to connect an IDE drive are different depending on the type of drive you are connecting. Use one of the following procedures for your drive connection. Connecting the first IDE CD-ROM drive or DVD-ROM drive: 1. Locate the three-connector signal cable that comes with your computer or with the new drive. 2. Locate the secondary IDE connector on the system board. See "Identifying parts on the system board" on page 24. 3. Connect one end of the signal cable to the drive and the other to the secondary IDE connector on the system board. To reduce electronic noise, use the connectors at the end of the cable only. 4. Your computer has extra power connectors for additional drives. Connect a power connector to the drive. Chapter 5. Installing Options 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
6.
Install the drive into the bay. Align the screw holes and install two screws to
secure the drive.
7.
Each integrated drive electronics (IDE) drive requires two cables; a four-wire
power cable that connects to the power supply and a signal cable that connects
to the system board. For a CD-ROM drive, you might also have an audio cable.
The steps to connect an IDE drive are different depending on the type of drive you
are connecting. Use one of the following procedures for your drive connection.
Connecting the first IDE CD-ROM drive or DVD-ROM drive:
1.
Locate the three-connector signal cable that comes with your computer or with
the new drive.
2.
Locate the secondary IDE connector on the system board. See “Identifying parts
on the system board” on page 24.
3.
Connect one end of the signal cable to the drive and the other to the secondary
IDE connector on the system board. To reduce electronic noise, use the
connectors at the end of the cable only.
4.
Your computer has extra power connectors for additional drives. Connect a
power connector to the drive.
Chapter 5. Installing Options
31