Lenovo Q200 Q200 Hardware Maintenance Manual - Page 21

Using Device

Get Lenovo Q200 PDF manuals and user guides View all Lenovo Q200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Chapter 5. Using the Setup Utility press Enter. 4. when prompted to confirm the password, type the password again. If you type the password correctly, the password will be installed. To delete a previously set user password, do the following : 1. From the Security menu, select Set User Password and press Enter. 2. when you type the user password. a message will display that Enter New Password. Press Enter and a message will display that indicates the password has been disabled. 3. Press any key to contine. Using Device PS/2 Mouse Support When this feature is set to Disable, the device of PS/2 Mouse Support is disabled and will not be displayed in the system configuration. To set Device, do the following: 1. Start the Setup Utility program (see "Starting the Setup Utility program" on page 16). 2. From the Setup Utility program menu, select Device. 3. Select PS/2 Mouse Support. 4. Select Disabled or Enabled or Auto and press Enter. 5. Return to the Setup Utility program menu and select Exit and then Save changes and Exit. Note If you do not want to save the settings, select Discard Changes and Exit or Discard Changes. You can set others such as Floppy Drive Setup,Serial Port Setup,Parallel Port Setup,USB Setup,ATA Drives Setup,Video Setup,Audio Setup,Network Setup and so on. See the information displayed on the right side of the screen. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
Chapter 5. Using the Setup Utility
19
press Enter.
4. when prompted to confirm the password, type the password again. If
you type the password correctly, the password will be installed.
To delete a previously set user password, do the following :
1. From the Security menu, select
Set User Password
and press
Enter
.
2. when you type the user password. a message will display that
Enter
New Password
. Press Enter and a message will display that indicates the
password has been disabled.
3. Press any key to contine.
Using Device
PS/2 Mouse Support
When this feature is set to
Disable
,
the device of PS/2 Mouse Support is
disabled and will not be displayed in
the system configuration.
To set Device, do the following:
1. Start the Setup Utility program (see “Starting the Setup Utility program”
on page 16).
2. From the Setup Utility program menu, select
Device
.
3. Select
PS/2 Mouse Support
.
4. Select
Disabled
or
Enabled
or
Auto
and press Enter.
5. Return to the Setup Utility program menu and select
Exit
and then
Save
changes and Exit
.
Note
If you do not want to save the settings, select
Discard Changes and
Exit
or
Discard Changes
. You can set others such as
Floppy Drive
Setup,Serial Port Setup,Parallel Port Setup,USB Setup,ATA Drives
Setup,Video Setup,Audio Setup,Network Setup
and so on. See the
information displayed on the right side of the screen.