Lenovo ThinkPad Yoga 12 (English) Hardware Maintenance Manual - ThinkPad Yoga - Page 41

Hibernation mode, Symptom-to-FRU index, Settings, Power, Sleep - docking station

Get Lenovo ThinkPad Yoga 12 PDF manuals and user guides View all Lenovo ThinkPad Yoga 12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

• For Windows 8.1: Go to the desktop and move your pointer to the top-right or bottom-right corner of the screen to bring up the charms. Then click Settings ➙ Power ➙ Sleep. . In certain circumstances, the computer goes into sleep mode automatically: • After a period of inactivity specified in power plan settings • When the battery power is low To cause the computer to return from sleep mode and resume operation, do one of the following: • Press the Fn key. • Press the power button. Also, in either of the following events, the computer automatically returns from sleep mode and resumes operation: • The ring indicator (RI) is signaled by a serial device or a PC Card device. • The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters sleep mode. Wait a few seconds before taking any action to reenter operation mode. Hibernation mode In hibernation mode, the following occurs: • The system status, RAM, VRAM, and setup data are stored on the hard disk drive or solid-state drive. • The system is powered off. Note: If the computer enters the hibernation mode while it is docked to the docking station or the port replicator, do not undock it before resuming normal operation. If you do undock it and then try to resume normal operation, you will get an error message, and you will have to restart the system. If you have defined one of the following actions as the event that causes the system to go into hibernation mode, perform that action. • Closing the lid. • Pressing the power button. Also, the computer goes into hibernation mode automatically after a period of inactivity specified in power plan settings. When the power is turned on, the computer returns from hibernation mode and resumes operation. The hibernation file in the boot record on the hard disk drive or solid-state drive is read, and system status is restored from the hard disk drive or solid-state drive. Symptom-to-FRU index This section contains following information: • "Numeric error codes" on page 36 • "Error messages" on page 37 • "Beep symptoms" on page 37 • "No-beep symptoms" on page 38 • "LCD-related symptoms" on page 38 • "Intermittent problems" on page 39 • "Undetermined problems" on page 39 Chapter 4. Related service information 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
• For Windows 8.1: Go to the desktop and move your pointer to the top-right or bottom-right corner of the
screen to bring up the charms. Then click
Settings
➙
Power
➙
Sleep
.
.
In certain circumstances, the computer goes into sleep mode automatically:
• After a period of inactivity specified in power plan settings
• When the battery power is low
To cause the computer to return from sleep mode and resume operation, do one of the following:
• Press the Fn key.
• Press the power button.
Also, in either of the following events, the computer automatically returns from sleep mode and resumes
operation:
• The ring indicator (RI) is signaled by a serial device or a PC Card device.
• The time set on the resume timer elapses.
Note:
The computer does not accept any input immediately after it enters sleep mode. Wait a few
seconds before taking any action to reenter operation mode.
Hibernation mode
In hibernation mode, the following occurs:
• The system status, RAM, VRAM, and setup data are stored on the hard disk drive or solid-state drive.
• The system is powered off.
Note:
If the computer enters the hibernation mode while it is docked to the docking station or the port
replicator, do not undock it before resuming normal operation. If you do undock it and then try to resume
normal operation, you will get an error message, and you will have to restart the system.
If you have defined one of the following actions as the event that causes the system to go into hibernation
mode, perform that action.
• Closing the lid.
• Pressing the power button.
Also, the computer goes into hibernation mode automatically after a period of inactivity specified in power
plan settings.
When the power is turned on, the computer returns from hibernation mode and resumes operation. The
hibernation file in the boot record on the hard disk drive or solid-state drive is read, and system status is
restored from the hard disk drive or solid-state drive.
Symptom-to-FRU index
This section contains following information:
• “Numeric error codes” on page 36
• “Error messages” on page 37
• “Beep symptoms” on page 37
• “No-beep symptoms” on page 38
• “LCD-related symptoms” on page 38
• “Intermittent problems” on page 39
• “Undetermined problems” on page 39
Chapter 4
.
Related service information
35