Lexmark Network Printer Device MarkNet Internal Print Server Quick Start
Lexmark Network Printer Device Manual
View all Lexmark Network Printer Device manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark Network Printer Device manual content summary:
- Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 1
MarkNet N2000 Series Internal Print Servers Quick Reference October 2001 www.lexmark.com - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 2
Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark is subject to restrictions as set forth in subparagraph (c)(1)(ii) Lexmark International, Inc., Lexington, KY 40550. Warranty The limited warranty you received with your printer - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 3
English MarkNet N2000 Series Internal Print Servers Quick Reference Step 1: Install the print server 2 Step 2: Attach a network cable 2 Step 3: Assign an IP address 4 Step 4: Print a network setup page 5 Step 5: Configure the network printer 6 Electronic emissions notices 9 1 - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 4
Guide that shipped with your printer for instructions about accessing the printer system board, installing option cards, and reinstalling the printer system board. Copies of your printer publications are available on Lexmark's Web site at www.lexmark.com. Step 2: Attach a network cable Attach - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 5
MarkNet N2000, N2001, and N2002 models Use these print servers to attach printers to an Ethernet or a Token-Ring network. Important: If you choose not to use the BNC port on the MarkNet N2002e, leave the end cap on the port to protect the card - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 6
gateway appear as non zero. Go to "Step 4: Print a network setup page" on page 5. If your network is not using DHCP, then you must manually assign an IP address. One of the easiest ways is to use the printer operator panel. To set the printer IP address, netmask, and gateway: 1 Press Menu until you - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 7
you are finished. The message Saved appears briefly. 7 Press Go to return the printer to the Ready state. Step 4: Print a network setup page Use the printer operator panel to print a network setup page to verify your IP settings. 1 Press Menu until you see Utilities, and then press Select. 2 Press - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 8
assigned and verified the TCP/IP settings, you are ready to configure the printer and set up your network clients to print to it. Windows In Windows environments, your network printers can be configured for direct printing or for shared printing. Supported printing methods • Direct IP printing - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 9
and on Lexmark's Web site at www.lexmark.com. Lexmark provides a printer driver package for each supported UNIX and Linux platform. The package contains all the necessary drivers and PPDs. The User's Guide in each package gives detailed instructions for installing and using Lexmark printers in UNIX - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 10
, and print to them. You can get the gateway, snap-ins, support files, and a white paper with installation instructions from Lexmark's Web site at www.lexmark.com/networking/ndps.html. Other information about installing network printers in NetWare environments is on the drivers CD that shipped with - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 11
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any and used in accordance with the instruction manual, may cause harmful interference to by the Director of Manufacturing and Technical Support, Lexmark International, S.A., Boigny, France. This - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 12
Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Japanese VCCI Notice The United Kingdom Telecommunications Act 1984 This apparatus is approved under the approval number NS - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 13
11 - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 14
Circle Road, Lexington, Kentucky 40550, EUA. No Reino Unido e na Irlanda, envie para Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. A Lexmark pode usar ou distribuir qualquer informação que você fornecer de qualquer forma que julgar - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 15
Português MarkNet série N2000 Servidores de impressão internos Referência rápida Etapa 1: Instalar o servidor de impressão 14 Etapa 2: Conectar o cabo da rede 14 Etapa 3: Definir um endereço IP 16 Etapa 4: Imprimir uma página de configuração de rede . 17 Etapa 5: Configurar a impressora da rede - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 16
como instalar placas opcionais e reinstalar a placa do sistema da impressora. Cópias das publicações da impressora estão disponíveis no site da Lexmark, www.lexmark.com. Etapa 2: Conectar o cabo da rede Conecte a impressora à rede usando um cabo de rede Ethernet ou Token-Ring. 1 Certifique-se de - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 17
MarkNet modelos N2000, N2001 e N2002 Use os servidores de impressão para conectar impressoras à rede Ethernet ou Token-Ring. Importante: Se você escolher não usar a porta BNC no MarkNet N2002e, deixe a tampa da extremidade na porta para proteger a placa da descarga eletrostática (ESD). MarkNet - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 18
MarkNet modelos N2004fl Use esses servidores de impressão para conectar impressoras a uma rede de fibra óptica FL 10Base ou uma rede Ethernet 10BaseTX. MarkNet N2004fl-SC MarkNet N2004fl-ST MarkNet N2004fl-MTRJ Etapa 3: Definir um endereço IP MENU REDE Menu Selecionar Você deve atribuir um - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 19
a Pressione Menu para aumentar (ou diminuir) cada número. b Pressione Selecionar para mover-se para o próximo segmento. c Pressione Selecionar novamente quando tiver terminado. A mensagem Salvo aparecerá rapidamente. 7 PressioneIr para retornar a impressora ao estado Pronta. Etapa 4: Imprimir uma - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 20
. Drivers personalizados estão disponíveis no CD de drivers. Drivers personalizados e de sistema atualizados estão disponíveis no site da Lexmark, www.lexmark.com. Criando portas e instalando drivers Leia as instruções detalhadas no CD de drivers. Clique em Visualizar documentação e procure pelas - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 21
Printer no site da Lexmark, www.lexmark.com. A Lexmark fornece um pacote do driver da impressora para cada plataforma UNIX e Linux suportada. O pacote Services (NDPS) como com ambientes regulares NetWare baseados em fila. NDPS Se você tem um ambiente NDPS, recomendamos que instale o Lexmark - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 22
com facilidade. Você pode obter o gateway, snap-ins, arquivos de suporte e um documento com as instruções de instalação no site da Lexmark, www.lexmark.com/networking/ndps.html. Outras informações sobre instalação de impressoras de rede em ambientes NetWare estão no CD de drivers enviado junto com - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 23
em um ambiente comercial. O equipamento gera, usa e pode emitir energia de radiofreqüência e, se não for instalado e usado de acordo com o manual de instrução, pode causar interferência prejudicial às comunicações de rádio. A operação desse equipamento em uma área residencial pode causar interfer - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 24
A declaração de conformidade com os requisitos das Diretrizes foi assinada pelo Diretor de produção e suporte técnico da Lexmark International, S.A., Boigny, França. Este produto satisfaz os limites da Classe A de EN 55022 e os requisitos de segurança de EN 60950. Aviso Este é um produto Classe A. - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 25
23 - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 26
Road, Lexington, Kentucky 40550, U.S.A. En Grande-Bretagne et en Irlande, envoyez vos commentaires à Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark peut utiliser ou diffuser toute information que vous lui fournirez, de la mani - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 27
Français MarkNet X2000 Series Serveurs d'impression internes Référence rapide Etape 1 : Installation du serveur d'impression 26 Etape 2 : Fixation d'un câble réseau 26 Etape 3 : Attribution d'une adresse IP 28 Etape 4 : Impression d'une page de configuration réseau . . . . .29 Etape 5 : - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 28
et la réinstallation de la carte mère, reportez-vous au Guide d'installation fourni avec l'imprimante. Des copies des publications de l'imprimante sont disponibles sur le site Web de Lexmark à l'adresse suivante : www.lexmark.com. Etape 2 : Fixation d'un câble réseau Branchez un câble réseau - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 29
Modèles MarkNet N2000, N2001 et N2002 Utilisez les serveurs d'impression suivants pour connecter les imprimantes à un réseau Ethernet ou Token-Ring. Important : Si vous n'utilisez pas le port BNC avec le modèle MarkNet N2002e, ne retirez pas le cache du port qui protège la carte contre toute dé - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 30
Modèles MarkNet N2004fl Utilisez les serveurs d'impression suivants pour connecter les imprimantes à un réseau à fibres optiques 10Base FL ou à un réseau Ethernet 10BaseTX. MarkNet N2004fl-SC MarkNet N2004fl-ST MarkNet N2004fl-MTRJ Etape 3 : Attribution d'une adresse IP MENU RESEAU Menu Sé - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 31
5 Appuyez sur Menu jusqu'à ce que Déf. adresse IP (ou Déf. masque IP ou Déf. passrlle IP) apparaisse, puis sur Sélectionner. 6 Pour définir l'adresse, le masque de réseau et la passerelle, procédez comme suit : a Appuyez sur Menu pour augmenter (ou diminuer) chaque valeur. b Appuyez sur Sélectionner - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 32
système mis à jour ainsi que des pilotes personnalisés sont disponibles sur le site Web de Lexmark à l'adresse suivante : www.lexmark.com. Création de ports et installation des pilotes Lisez les instructions détaillées qui figurent sur le CD Pilotes. Cliquez sur Afficher les documents en ligne et - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 33
PPD (PostScript Printer Description) contient afin de créer une file d'attente dans le centre d'impression guide de l'utilisateur accompagnant chaque paquetage fournit des instructions détaillées sur l'installation et l'utilisation des imprimantes Lexmark dans les environnements UNIX et Linux - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 34
obtenir la passerelle, des snap-in, des fichiers de support ainsi que de la documentation technique contenant des instructions d'installation sur le site Web de Lexmark à l'adresse suivante : www.lexmark.com/networking/ndps.html. Vous trouverez des informations supplémentaires sur l'installation - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 35
de l'énergie radioélectrique haute fréquence. Par ailleurs, l'installation ou l'utilisation du matériel de manière non conforme aux instructions du fabricant risque de provoquer des interférences nuisibles aux communications radio. L'exploitation de ce matériel dans une zone résidentielle peut - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 36
Une déclaration de conformité aux exigences de la directive a été signée par le directeur de la production et du support technique, Lexmark International, S.A., Boigny, France. Ce produit est conforme aux normes établies par la réglementation EN 55022 et applicables à la classe A ainsi qu'aux - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 37
35 - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 38
und Irland richten Sie Ihre Kommentare an Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark darf alle von Ihnen bereitgestellten Informationen in jeder von Lexmark als angemessen erachteten Weise verwenden oder verbreiten - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 39
Deutsch MarkNet N2000 Series Interne Druckserver Kurzanleitung Schritt 1: Installieren des Druckservers 38 Schritt 2: Anschließen eines Netzwerkkabels 38 Schritt 3: Zuweisen einer IP-Adresse 40 Schritt 4: Drucken einer Netzwerk-Konfigurationsseite . . 41 Schritt 5: Konfigurieren des - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 40
Druckers, zum Installieren von Optionskarten und zum Wiederanbringen der Systemplatine. Kopien der Veröffentlichungen zum Drucker stehen auf der Lexmark Website unter www.lexmark.com zur Verfügung. Schritt 2: Anschließen eines Netzwerkkabels Binden Sie den Drucker mit einem Ethernet- oder Token - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 41
Modelle MarkNet N2000, N2001 und N2002 Verwenden Sie diese Druckserver, um Drucker in ein Ethernet- oder Token-Ring-Netzwerk einzubinden. Wichtig: Wenn Sie den BNC-Anschluß auf der MarkNet N2002eKarte nicht verwenden möchten, entfernen Sie die Endkappe nicht vom Anschluß, um die Karte vor - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 42
MarkNet N2004flModelle Verwenden Sie diese Druckserver, um Drucker in ein 100Base FLGlasfaser-Netzwerk oder ein Ethernet 10BaseTX-Netzwerk einzubinden. MarkNet N2004fl-SC MarkNet N2004fl-ST MarkNet N2004fl-MTRJ Schritt 3: Zuweisen einer IP-Adresse MENÜ NETZWERK Menü Auswählen Sie müssen - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 43
6 So legen Sie die Adresse, die Netzmaske und das Gateway fest: a Drücken Sie Menü, um die Zahlen zu erhöhen oder zu verringern. b Drücken Sie Auswählen, um zum nächsten Segment zu gelangen. c Drücken Sie abschließend erneut die Taste Auswählen. Die Meldung Gespeichert wird kurz angezeigt. 7 Drücken - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 44
. Angepaßte Treiber stehen auf der Treiber-CD zur Verfügung. Aktualisierte Treiber (System und angepaßt) können von der Lexmark Website unter www.lexmark.com heruntergeladen werden. Erstellen von Anschlüssen und Installieren von Treibern Lesen Sie die ausführlichen Anweisungen auf der Treiber-CD - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 45
Netzwerk-Clients einsatzbereit sichtbar. Note: Eine PostScript Printer Description-Datei (PPD) enthält detaillierte Informationen als auch auf der Lexmark Website unter www.lexmark.com zur Verfügung. Lexmark stellt ein Druckertreiberpaket für jede unterstützte UNIXund Linux-Plattform bereit. Das - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 46
. Das Gateway sowie Snap-Ins, Unterstützungsdateien und ein Weißbuch mit Installationsanweisungen können unter www.lexmark.com/networking/ndps.html von der Lexmark Website heruntergeladen werden. Weitere Informationen zur Installation von Netzwerkdruckern in NetWare-Umgebungen finden Sie auf der im - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 47
Hinweise zu Elektro-Emissionen FCC-Bestimmungen Der interne MarkNet-Druckserver wurde gemäß Teil 15 der FCCBestimmungen getestet und entspricht den Grenzwerten für ein Digitalgerät der Klasse A. Der Betrieb unterliegt folgenden zwei Einschränkungen: (1) Dieses Gerät darf keine schädlichen Stö - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 48
ausgelegt sind. Eine Erklärung der Erfüllung der Anforderungen der Richtlinie wurde durch den Vorstand für Fertigung und Technische Unterstützung, Lexmark International, S.A., Boigny, Frankreich, unterzeichnet. Dieses Produkt erfüllt die Grenzwerte der Norm EN 55022 für Geräte der Klasse A und die - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 49
47 - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 50
New Circle Road, Lexington, Kentucky 40550, U.S.A. Per il Regno Unito e l'Eire, l'indirizzo è Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark si riserva il diritto di utilizzare o divulgare le informazioni ricevute nei modi - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 51
Italiano MarkNet Serie N2000 Server di stampa interni Guida rapida Passo 1: Installazione del server di stampa 50 Passo 2: Collegamento del cavo di rete 50 Passo 3: Assegnazione di un indirizzo IP 52 Passo 4: Stampa di una pagina delle impostazioni di rete . . . 53 Passo 5: Configurazione della - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 52
di stampa Installare il server di stampa interno MarkNet™ Lexmark™ in un alloggiamento per scheda opzionale disponibile all'interno copie delle pubblicazioni della stampante sono disponibili presso il sito Web Lexmark: www.lexmark.com. Passo 2: Collegamento del cavo di rete Collegare la stampante - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 53
Modelli MarkNet N2000, N2001 e N2002 Utilizzare questi server di stampa per collegare le stampanti a una rete Ethernet o Token-Ring. Importante: se non si desidera utilizzare la porta BNC sul modello MarkNet N2002e, non rimuovere la protezione sull'estremità della porta per proteggere la scheda da - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 54
Modelli MarkNet N2004fl Utilizzare questi server di stampa per collegare le stampanti alla rete a fibre ottiche 10Base FL o a una rete Ethernet 10BaseTX. MarkNet N2004fl-SC MarkNet N2004fl-ST MarkNet N2004fl-MTRJ Passo 3: Assegnazione di un indirizzo IP MENU RETE Menu Seleziona Per - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 55
6 Per impostare l'indirizzo, la netmask e il gateway: a Premere Menu per aumentare o ridurre ciascun numero. b Premere Seleziona per passare al segmento successivo. c Al termine, premere di nuovo Seleziona. Viene brevemente visualizzato il messaggio Salvato. 7 Premere OK per riportare la stampante - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 56
le funzioni, ad esempio gli stati di avviso della stampante. Porte delle stampanti di rete supportate • Porta IP Microsoft (Windows NT 4.0, Windows 2000 e Windows XP) • Porta di rete Lexmark (Windows 95/98/Me, Windows NT 4.0, Windows 2000 e Windows XP) Driver per stampante supportati • Driver - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 57
nel centro di stampa utilizzando il PostScript Printer Module e il file PPD personalizzato della stampante. Le informazioni Lexmark www.lexmark.com. Lexmark fornisce un pacchetto di driver per stampante per ciascuna piattaforma UNIX e Linux supportata. Tale pacchetto contiene tutti i driver e i file - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 58
Services) che in normali ambienti NetWare basati su coda. NDPS Se si utilizza un ambiente NDPS, si consiglia di installare il Gateway IP NDPS Lexmark in, i file di supporto e le istruzioni di installazione sono disponibili presso il sito Web Lexmark all'indirizzo: www.lexmark.com/networking/ndps.html - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 59
di voltaggio. La dichiarazione di conformità ai requisiti delle direttive è stata firmata dal Direttore della produzione e dell'assistenza tecnica della Lexmark International, S.A., Boigny, Francia. Questo prodotto è conforme ai limiti EN 55022 per la Classe A ed ai requisiti di sicurezza EN 60950 - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 60
Avvertenza Questo è un prodotto di classe A. L'uso di questa apparecchiatura in un'area residenziale potrebbe causare interferenze radio. Pertanto, all'utente potrebbe essere richiesto di prendere adeguati provvedimenti. Avvertenza VCCI per il Giappone The United Kingdom Telecommunications Act - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 61
59 - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 62
Circle Road, Lexington, Kentucky 40550, EE.UU. En el Reino Unido e Irlanda, diríjase a Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark puede utilizar o distribuir cualquier información que le suministren de la forma que crea - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 63
Español Servidores de impresión internos MarkNet N2000 Series Referencia rápida Paso 1: Instalación del servidor de impresión 62 Paso 2: Conexión del cable de red 62 Paso 3: Asignación de una dirección IP 64 Paso 4: Impresión de una página de configuración de la red . . . 65 Paso 5: Configuraci - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 64
acceder a la placa del sistema de la impresora, cómo instalar tarjetas de opción y volver a colocar la placa del sistema. El sitio Web de Lexmark en www.lexmark.com contiene copias de las publicaciones de la impresora. Paso 2: Conexión del cable de red Conecte la impresora a la red con un cable de - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 65
Modelos MarkNet N2000, N2001 y N2002 Utilice estos servidores de impresión para conectar las impresoras a una red Ethernet o Token-Ring. Importante: si decide no utilizar el puerto BNC del servidor MarkNet N2002e, deje en el puerto el terminador para proteger la tarjeta de una descarga por - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 66
Modelos Utilice estos servidores de impresión para conectar impresoras a una MarkNet N2004fl red de fibra óptica 10Base FL o Ethernet 10BaseTX. MarkNet N2004fl-SC MarkNet N2004fl-ST MarkNet N2004fl-MTRJ Paso 3: Asignación de una dirección IP MENÚ RED Menú Seleccionar Debe asignar una direcci - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 67
6 Para establecer la dirección, la máscara de red o el gateway. a Pulse Menú para aumentar (o reducir) cada número. b Pulse Seleccionar para desplazarse al siguiente segmento. c Vuelva a pulsar Seleccionar cuando haya terminado. Aparecerá el mensaje Guardado brevemente. 7 Pulse Continuar para - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 68
de la impresora. Puertos de impresoras de red admitidos • Puerto Microsoft IP (Windows NT 4.0, Windows 2000 y Windows XP) • Puerto de red Lexmark (Windows 95/98/Me, Windows NT 4.0, Windows 2000 y Windows XP) Controladores de impresora admitidos • Controladores de impresora de sistemas Windows - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 69
Sun Solaris está situado en el CD de controladores y en el sitio Web de Lexmark en www.lexmark.com. Lexmark proporciona un paquete de controladores de impresora para cada plataforma UNIX y Linux admitida. Este paquete contiene todos los controladores y archivos PPD necesarios. La Guía del usuario - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 70
el gateway, las incorporaciones, los archivos de soporte y un informe técnico con instrucciones de instalación del sitio Web de Lexmark en www.lexmark.com/networking/ndps.html. El CD de controladores incluido con la impresora contiene más información sobre la instalación de impresoras de red en - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 71
equipos eléctricos diseñados para su uso dentro de unos determinados límites de voltaje. El director de fabricación y servicio técnico de Lexmark International, S.A. de Boigny, Francia ha firmado una declaración de conformidad con los requisitos de la directiva. Este producto cumple los límites de - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 72
Advertencia Éste es un producto de Clase A. En un entorno doméstico, este producto puede causar interferencias de radio, en cuyo caso, se solicitará al usuario que adopte las medidas oportunas. Aviso VCCI japonés Ley de telecomunicaciones de 1984 del Reino Unido This apparatus is approved under - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 73
This is a placeholder for the inside back cover. - Lexmark Network Printer Device | MarkNet Internal Print Server Quick Start - Page 74
P/N 10P0061 E.C. 1P0001A Lexmark, Lexmark with diamond design, and MarkNet are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. © 2001 Lexmark International, Inc. 740 West New Circle Road Lexington, Kentucky 40550 www.lexmark.com
Quick Reference
October 2001
MarkNet N2000 Series
Internal Print Servers
www.lexmark.com