LiftMaster TLS1CARD Owners Manual - English
LiftMaster TLS1CARD Manual
 |
View all LiftMaster TLS1CARD manuals
Add to My Manuals
Save this manual to your list of manuals |
LiftMaster TLS1CARD manual content summary:
- LiftMaster TLS1CARD | Owners Manual - English - Page 1
has different configuration modes that determine how the TLS1CARD will function. MODE COMPARABLE MODIFICATION DESCRIPTION TCP Mode 1 90-T1, 90- that all three inputs have a switch connected to the TLS1CARD. Either the external close, external safety, external open, or all three may be used. 1 - LiftMaster TLS1CARD | Owners Manual - English - Page 2
power to the operator and fully open or close the • LiftMaster Monitored Entrapment Protection (LMEP) devices door BEFORE installing ANY entrapment Logic 4 (L4) operator, the Timer Light Status Option Card (TLS1CARD) provides special functionality to control AVE auxiliary devices such as lights, - LiftMaster TLS1CARD | Owners Manual - English - Page 3
open mid-stop. • Connect a green light to the R2 terminals on the TLS1CARD. This will signal that the door is fully open or at the open mid position. • Connect an audio/visual signalling device to the R3 terminals on the TLS1CARD. This will signal that the door is closing. Inputs: • If the - LiftMaster TLS1CARD | Owners Manual - English - Page 4
modification 90-T2. 1 Disconnect power to the operator. 2 Turn DIP switch 4 on the TLS1CARD to the ON position. All other DIP switches should remain OFF. TCP MODE 2 DIP * ON* ON* OFF NOTES: • Relay LEDs R1, R2, and R3 on the TLS1CARD will turn ON at the same time as relays R1, R2, and R3. • * - LiftMaster TLS1CARD | Owners Manual - English - Page 5
position. • Connect an audio/visual signalling device to the R3 terminals on the TLS1CARD. This will signal that the door is in motion. Inputs: • If the OFF ON OFF OFF OFF ON NOTES: • Relay LEDs R1, R2, and R3 on the TLS1CARD will turn ON at the same time as relays R1, R2, and R3. • During - LiftMaster TLS1CARD | Owners Manual - English - Page 6
OFF OFF OFF OFF NOTES: • Relay LEDs R1, R2, and R3 on the TLS1CARD will turn ON at the same time as relays R1, R2, and R3. • 1 SIO 8 COMMON 7 5 A, 230 Vac, 30 Vdc Dry Contact Only TLS1CARD Timer Light Status Option Card 40-35757-1 2-Position Maintained Switch After configurations and - LiftMaster TLS1CARD | Owners Manual - English - Page 7
modification 90-T3. 1 Disconnect power to the operator. 2 Turn DIP switch 2 on the TLS1CARD to the ON position. All other DIP switches should remain OFF. TCP MODE 5 DIP * ON* ON* OFF NOTES: • Relay LEDs R1, R2, and R3 on the TLS1CARD will turn ON at the same time as relays R1, R2, and R3. • * - LiftMaster TLS1CARD | Owners Manual - English - Page 8
the open mid-stop. • Connect a yellow light to the R3 terminals on the TLS1CARD. This will signal that the door is not in motion or not fully closed. OFF ON or Flash ON OFF ON OFF NOTE: Relay LEDs R1, R2, and R3 on the TLS1CARD will turn ON at the same time as relays R1, R2, and R3. TC MODE 1 - LiftMaster TLS1CARD | Owners Manual - English - Page 9
: It is not required that all three inputs have a switch connected to the TLS1CARD. Either the external close, external safety, external open, or all three may be OFF R3 LED OFF ON OFF NOTE: Relay LEDs R1, R2, and R3 on the TLS1CARD will turn ON at the same time as relays R1, R2, and R3. SP - LiftMaster TLS1CARD | Owners Manual - English - Page 10
ERROR CODES Error Description Solution Board Communication Error Ensure TLS1CARD is seated properly and power cycle the operator. Improper Mode Setting Refer to manual for proper selection. DIP Switch Changed During Operation Check mode and reset the operator board by moving the selector - LiftMaster TLS1CARD | Owners Manual - English - Page 11
after a specified amount of time, like apartment buildings or fire stations. REQUIREMENTS The application MUST have at least one of the following LiftMaster Monitored Entrapment Protection (LMEP) devices installed: CPS-U, CPS-UN4, or a CPS-EI with a valid door sensing edge. Wiring type must be set - LiftMaster TLS1CARD | Owners Manual - English - Page 12
PROGRAMMING PRE-WARNING NOTE: The TTC must be programmed prior to this step. 1 Turn the selector dial to OPTN. 2 Press and release the TTC button on the logic board. 3 Press and release the STOP button to clear the Pre-Warning setting. 4 Press and release the OPEN button for every second of Pre-
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
1
TLS1CARD
TIMER LIGHT STATUS OPTION CARD
The TLS1CARD has different configuration modes that determine how the TLS1CARD will function.
MODE
COMPARABLE MODIFICATION
DESCRIPTION
TCP Mode 1
90-T1, 90-515774, or RDGRNCARD
•
3 relay outputs (R1, R2, and R3) with optional flashing for R1
•
Adjustable Pre-Warning
•
R1 output on during Pre-Warning, while in motion, and at an
undefined stopped position
•
R2 output on at fully open and at open mid-stop
•
R3 output on while closing only
TCP Mode 2
90-T2
•
3 relay outputs (R1, R2, and R3)
•
Adjustable Pre-Warning
•
R1 output on during Pre-Warning only
•
R2 output on at fully open
•
R3 output on only when a special input to open has been used to
open the door which does not activate the Timer-to-Close
TCP Mode 3
90-T4
•
3 relay outputs (R1, R2, and R3)
•
Adjustable Pre-Warning
•
R1 output on during Pre-Warning only
•
R2 output on at fully open and at open mid-stop
•
R3 output on while in motion
TCP Mode 4
90-RGLFCIR or 90-HDFLASH2
•
2 relay outputs (R1, R2) with optional flashing for R1
•
Adjustable Pre-Warning
•
R1 output on during Pre-Warning and while closing
•
R2 output on at fully open
TCP Mode 5
90-T3
•
3 relay outputs (R1, R2, and R3)
•
Adjustable Pre-Warning
•
R1 output on at all times except fully open and fully closed
•
R2 output on at fully open
•
R3 output on only when a special input to open has been used to
open the door which does not activate the Timer-to-Close
TC Mode 1
90-L3FLASH
•
3 relay outputs (R1, R2, and R3) with optional flashing for R1
•
R1 output on while in motion
•
R2 output on at fully open and at open mid-stop
•
R3 output on at fully open, open mid-stop, and at an undefined
stopped position
SP Mode 1
90-42104
This mode allows a second set of external, track mounted limits to act
as primary or backup for the operator’s open, close, and safety limits.
NOTE:
It is not required that all three inputs have a switch connected to
the TLS1CARD. Either the external close, external safety, external open,
or all three may be used.