Linksys PCM200 User Guide - Page 6
Installing the EtherFast 10/100, CardBus PC Cards - software
UPC - 745883549450
View all Linksys PCM200 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
Linksys Instant EtherFast® Series Installing the EtherFast 10/100 CardBus PC Cards Getting the Right Cable Like most network devices, the EtherFast Card must be connected to a 10BaseT or Fast Ethernet hub with the right kind of twisted-pair network cabling. Although twisted-pair is available in different styles and grades, a category 5 network cable with RJ-45 tips that does not exceed 100 meters (328 feet) in length is required. Cabling can be obtained at most computer stores. If you are using Fast Ethernet, Category 5 (or better) cable must be used. For more information about Fast Ethernet cabling, including information on how to crimp your own cables, go to page 49. Installing the CardBus PC Card and Cabling 1. Turn off your PC and any devices attached to it. 2. If you are installing the standard PC Card, snap the flat end of the media coupler into the EtherFast 10/100 CardBus PC Card. It should lock firmly into place. 3. Locate your PC's CardBus slot (usually located on the side). Slide the EtherFast 10/100 CardBus PC Card into the slot with the triangle on the card facing up. The 128-pin end goes in first. See that the card is seated snugly in place. Note: If the PC Card does not fit all the way into the slot, check your PC's documentation to be sure that your laptop has a CardBus slot. 4. Attach one end of a category 5 network cable into the RJ-45 port on the end of the EtherFast Card or media coupler. Then plug the other end of the cable into a Fast Ethernet or 10BaseT hub. The EtherFast 10/100 CardBus PC Card will automatically sense the type, polarity, and speed of your network's cabling and adjust itself accordingly. 6 EtherFast® 10/100 CardBus PC Cards About the Software The EtherFast 10/100 CardBus PC Card requires two different kinds of software in order to work: Socket and card services are special software drivers that allow a PC card to communicate with your computer. Your computer might have services that were installed by the manufacturer, making your PC compatible with a wide range of CardBus and PCMCIA cards. If your computer doesn't have services, or if you're not sure how to get yours working, the EtherFast 10/100 CardBus PC Card comes with a generic enabler you can use to get the card up and running in your DOS or Windows NT computer's card slot. Card services are always loaded into memory each time your PC is started up, and always before your network drivers are loaded. Network drivers allow the card to communicate with your network at large. The EtherFast 10/100 CardBus PC Card disk includes drivers for many network operating systems, including Windows 95, 98, 2000, NT, Windows for Workgroups, NetWare, packet driver networks, and more. When the EtherFast 10/100 CardBus PC Card is up and running, it will talk to your PC's card slot, which will talk to the Card services, which will finally talk to the network drivers and the network at large. Choosing I/O and IRQ Values Just like modems, mice, CD-ROMs, hard drives, and other devices, the EtherFast 10/100 CardBus PC Card requires an I/O address and IRQ value for it to use. An I/O base address is the Input/Output area of your computer's Input/Output range that the EtherFast 10/100 CardBus PC Card will use for transferring data to and from a network. The I/O value you assign to the EtherFast 10/100 CardBus PC Card must not be in use by any other devices. I/O values are always expressed in hexadecimal values. A hexadecimal value is basically a number that serves as an abbreviation of a larger number. Also known as an interrupt, an IRQ is a signal that notifies the PC when certain input or output events have occurred and where the attention of the PC is needed. IRQs are expressed in numerical values. Your computer's system BIOS will automatically assign an IRQ value. 7