Linksys PCMLM56 User Guide - Page 16

card's IRQ, I/O, COM, modem IRQ, or slot settings. Try, 100 + 56K Modem PC Card into one of your PC's - etherfast drivers

Get Linksys PCMLM56 - EtherFast - 56 Kbps Network PDF manuals and user guides
UPC - 745883548958
View all Linksys PCMLM56 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Services c:\carden /IRQ=10 /IOP=320 /COM=2 /MIR=3 /slt=0 9. Save your new AUTOEXEC.BAT file. The card and socket services setup is complete. Power down your computer and insert the EtherFast 10/100 + 56K Modem PC Card into one of your PC's PCMCIA slots. Restart your PC. When the enabler command in the AUTOEXEC.BAT file is executed, you should see a message that looks similar to this scroll by (it may vary): PCMCIA Ethernet Client Driver v3.00 IO Base = 0X030, IRQ=10, COM=02, MIR=3, slot = 0 You may also hear an audible tone indicating that the card was successfully initialized. If you received an error message, or a message stating that the 10/100 + 56K Modem PC Card was not installed successfully, you might need to change the card's IRQ, I/O, COM, modem IRQ, or slot settings. Try different values until you find a combination that works. Remember that each time you try a different value with enabler, you should also change the value in your communication software. For more general information about I/O and IRQ settings, see page 7. To check to settings assigned to the card, run the following command from a DOS prompt: c:\carden /chk 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
c:\carden /IRQ=10 /IOP=320 /COM=2
/MIR=3 /slt=0
9. Save your new AUTOEXEC.BAT file. The card and
socket services setup is complete.
Power down your computer and insert the EtherFast
10/100 + 56K Modem PC Card into one of your PC’s
PCMCIA slots.
Restart your PC. When the enabler command in the
AUTOEXEC.BAT file is executed, you should see a
message that looks similar to this scroll by (it may
vary):
PCMCIA Ethernet Client Driver v3.00
IO Base = 0X030, IRQ=10, COM=02, MIR=3, slot = 0
You may also hear an audible tone indicating that the
card was successfully initialized.
If you received an error message, or a message stating
that the 10/100 + 56K Modem PC Card was not
installed successfully, you might need to change the
card's IRQ, I/O, COM, modem IRQ, or slot settings. Try
different values until you find a combination that works.
Remember that each time you try a different value with
enabler, you should also change the value in your com-
munication software. For more general information
about I/O and IRQ settings, see page 7.
To check to settings assigned to the card, run the follow-
ing command from a DOS prompt:
c:\carden /chk
14
Services