MSI Eclipse User Guide - Page 142

Install Driver in Windows Vista / XP

Get MSI Eclipse PDF manuals and user guides View all MSI Eclipse manuals
Add to My Manuals
Save this manual to your list of manuals

Page 142 highlights

JMicron RAID Installing Driver Install Driver in Windows Vista / XP † New Windows Vista / XP Installation The following details the installation of the drivers while installing W indows XP. 1. W hen you start installing Windows XP and older operating systems, you may encounter a message stating, "Setup could not determine the type of one or more mass storage devices installed in your system". If this is the case, then you are already in the right place and are ready to supply the driver. If this is not the case, then press F6 when prompted at the beginning of W indows setup. 2. Press the "S" key to select "Specify Additional Device". 3. You should be prompted to insert a floppy disk containing the JMicron RAID driver into the A: drive. Note: For W indows XP, you can use the USB floppy drive only. For W indows Vista you can use CD/ DVD/ USB drive. Important Please follow the instruction below to make an "JMicron RAID Driver" for yourself. 1. Insert the MSI CD into the CD-ROM drive. 2. Click the "Browse CD" on the Setup screen. 3. Copy all the contents in the \\IDE\JMicron\Floppy32 (for 32-bit OS) or \\IDE\JMicron\Floppy64 (for 64-bit OS) to a formatted floppy drive. 4. The driver diskette for JM icron RAID Controller is done. 4. W hen prompted, insert the floppy disk you created in step 3 and press Enter. 5. You should be shown a list of available SCSI Adapters. 6. Select the appropriate JMicron RAID controller and press ENTER. 7. The next screen should confirm that you have selected the JMicron RAID controller. Press ENTER again to continue. 8. You have successfully installed the JMicron RAID driver, and Windows setup should continue. 9. Leave the disk in the floppy drive until the system reboots itself. W indows setup will need to copy the files from the floppy again after the RAID volume is formatted, and W indows setup starts copying files. For W indows Vista: After selecting the location to install W indows Vista, please click on the "Load Driver" button to install the RAID driver. Please refer the Important notice above to make a RAID Driver medium. And then, follow the instructions to complete the RAID drive installation and the W indows Vista installation. D-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
D-11
JMicron RAID
Installing Driver
Install Driver in Windows Vista / XP
°
New Windows Vista / XP Installation
The following details the installation of the drivers while installing Windows XP.
1.
When you start installing Windows XP and older operating systems, you may
encounter a message stating,
“
Setup could not determine the type of one or
more mass storage devices installed in your system
”
. If this is the case, then
you are already in the right place and are ready to supply the driver. If this is
not the case, then press F6 when prompted at the beginning of Windows
setup.
2.
Press the
“
S
”
key to select
“
Specify Additional Device
”
.
3.
You should be prompted to insert a floppy disk containing the JMicron
RAID
driver into the A: drive.
Note:
For Windows XP, you can use the USB floppy drive only.
For Windows Vista you can use CD/ DVD/ USB drive.
4.
When prompted, insert the floppy disk you created in step 3 and press Enter.
5.
You should be shown a list of available SCSI Adapters.
6.
Select the appropriate JMicron RAID controller and press ENTER.
7.
The next screen should confirm that you have selected the JMicron
RAID
controller. Press ENTER again to continue.
8. You have successfully installed the JMicron RAID driver, and Windows setup
should continue.
9. Leave the disk in the floppy drive until the system reboots itself. Windows
setup will need to copy the files from the floppy again after the RAID volume
is formatted, and Windows setup starts copying files.
For Windows Vista:
After selecting the location to install Windows Vista, please click on the
“
Load
Driver
”
button to install the RAID driver. Please refer the
Important
notice above
to make a RAID Driver medium. And then, follow the instructions to complete the
RAID drive installation and the Windows Vista installation.
Important
Please follow the instruction below to make an
“
JMicron RAID Driver
”
for
yourself.
1. Insert the MSI CD into the CD-ROM drive.
2. Click the
“
Browse CD
”
on the Setup screen.
3. Copy all the contents in the
\\IDE\JMicron\Floppy32
(for 32-bit OS) or
\\IDE\JMicron\Floppy64
(for 64-bit OS) to a formatted floppy drive.
4. The driver diskette for
JMicron RAID Controller
is done.