MSI Master LS2 User Guide - Page 61

OnChip IDE Device, IDE HDD Block Mode, On-Chip Primary/Secondary PCI IDE, IDE Primary/Secondary - and commander

Get MSI Master LS2 - E7505 Motherboard - Extended ATX PDF manuals and user guides
UPC - 816909003086
View all MSI Master LS2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

BIOS Setup Off On Former-Sts Leaves the computer in the power off state. Reboots the computer. Restores the system to the status before power failure or interrupt occurs. OnChip IDE Device Press to enter the sub-menu and the following screen appears: IDE HDD Block Mode This allows your hard disk controller to use the fast block mode to transfer data to and from the hard disk drive. Block mode is also called block transfer, multiple commands or multiple sector read/write. Enabled enables IDE controller to use block mode; Disabled allows the controller to use standard mode. On-Chip Primary/Secondary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels. Choose Enabled to activate each channel separately. IDE Primary/Secondary Master/Slave PIO The four items allow you to set a PIO (Programmed Input/Output) mode for each of the four IDE devices that the onboard IDE interface supports. Modes 0~4 provide increased performance. In Auto mode, BIOS automatically determines the best mode for each IDE device. IDE Primary/Secondary Master/Slave UDMA Ultra DMA implementation is possible only if your IDE device supports 3-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
3-17
BIOS Setup
Off
Leaves the computer in the power off state.
On
Reboots the computer.
Former-Sts
Restores the system to the status before power failure or
interrupt occurs.
OnChip IDE Device
Press <Enter> to enter the sub-menu and the following screen appears:
IDE HDD Block Mode
This allows your hard disk controller to use the fast block mode to trans-
fer data to and from the hard disk drive. Block mode is also called block
transfer, multiple commands or multiple sector read/write.
Enabled
ena-
bles IDE controller to use block mode;
Disabled
allows the controller to
use standard mode.
On-Chip Primary/Secondary PCI IDE
The integrated peripheral controller contains an IDE interface with sup-
port for two IDE channels. Choose
Enabled
to activate each channel
separately.
IDE Primary/Secondary Master/Slave PIO
The four items allow you to set a PIO (Programmed Input/Output) mode
for each of the four IDE devices that the onboard IDE interface supports.
Modes 0~4
provide increased performance.
In
Auto
mode, BIOS auto-
matically determines the best mode for each IDE device.
IDE Primary/Secondary Master/Slave UDMA
Ultra DMA implementation is possible only if your IDE device supports