MSI Master LS2 User Guide - Page 66

PNP/PCI Configurations

Get MSI Master LS2 - E7505 Motherboard - Extended ATX PDF manuals and user guides
UPC - 816909003086
View all MSI Master LS2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

MS-9121 E-ATX Mainboard PNP/PCI Configurations This section describes configuring the PCI bus system and PnP (Plug & Play) feature. PCI, or Peripheral Component Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. Reset Configuration Data Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on card and the system reconfiguration has caused such a serious conflict that the operating system cannot boot. Setting options: Enabled, Disabled. Resource Controlled By The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices. However, this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows® 95/98. If you set this field to "manual" choose specific resources by going into each of the sub menu that follows this field (a sub menu is preceded by a "¾"). The settings are: Auto (ESCD), Manual. 3-22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
3-22
MS-9121 E-ATX Mainboard
PNP/PCI Configurations
This section describes configuring the PCI bus system and PnP (Plug &
Play) feature.
PCI, or
P
eripheral
C
omponent
I
nterconnect, is a system which
allows I/O devices to operate at speeds nearing the speed the CPU itself uses
when communicating with its special components.
This section covers some
very technical items and it is strongly recommended that only experienced
users should make any changes to the default settings.
Reset Configuration Data
Normally, you leave this field
Disabled
. Select
Enabled
to reset Extended
System Configuration Data (ESCD) when you exit Setup if you have installed
a new add-on card and the system reconfiguration has caused such a serious
conflict that the operating system cannot boot.
Setting options:
Enabled
,
Disabled
.
Resource Controlled By
The Award Plug and Play BIOS has the capacity to automatically configure
all of the boot and Plug and Play compatible devices. However, this capability
means absolutely nothing unless you are using a Plug and Play operating sys-
tem such as Windows
®
95/98. If you set this field to “manual” choose specific
resources by going into each of the sub menu that follows this field (a sub
menu is preceded by a “
”). The settings are:
Auto (ESCD)
,
Manual
.