MSI PM8PM-V User Guide - Page 14

ATX 24-Pin Power Connector: CONN1 - mainboard

Get MSI PM8PM-V - Motherboard - Micro ATX PDF manuals and user guides
UPC - 816909035261
View all MSI PM8PM-V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

ATX 24-Pin Power Connector: CONN1 This connector allows you to connect an ATX 24-pin power supply. To connect the ATX 24-pin power supply, make sure the plug of the power supply is inserted in the proper orientation and the pins are aligned. Then push down the power supply firmly into the connector. You may use the 20-pin ATX power supply as you like. If you'd like to use the 20-pin ATX power supply, please plug your power supply along with pin 1 & pin 13. There is also a foolproof design on pin 11, 12, 23 & 24 to avoid wrong installation. NC +12V +12V 5VSB PWR OK GND +5V GND +5V GND + 3 .3 V + 3 .3 V 12 24 1 13 GND +5V +5V +5V Res GND GND GND PS -O N # GND -12V +3.3V ATX 12V Power Connector: JPW1 12V This 12V power connector is used to provide power to the CPU. 12V 42 31 GND GND Floppy Disk Drive Connector: FDD1 The mainboard provides a standard floppy disk drive connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. IDE Connector: IDE1/ IDE2 The mainboard has dual Ultra DMA 33/66/100/133 controller that provides PIO mode 0~4, Bus Master, and Ultra DMA 66/100 function. You can connect up to four hard disk drives, CD-ROM, 120MB Floppy and other devices. The first hard drive should always be connected to IDE1. IDE1 can connect a Master and a Slave drive. You must configure second hard drive to Slave mode by setting the jumper accordingly. MSI Reminds You... If you install two hard disks on one cable, you must configure the second drive to Slave mode by setting its jumper. Refer to the hard disk documentation supplied by hard disk vendors for jumper setting instructions. Serial ATA Connectors: SATA1/ SATA2 7 The mainboard provides dual high-speed Serial ATA interface ports. These ports support 1st generation Serial ATA data rates of 150MB/s and are fully compliant with Serial ATA 1 1.0 specifications. Each Serial ATA connector can connect to 1 hard disk device. MSI Reminds You... Please do not fold the serial ATA cable in a 90-degree angle, which will cause the loss of data during transmission. CD-In Connector: CD_IN1 R The connector is for CD-ROM audio connector. GND L 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
8
ATX 24-Pin Power Connector: CONN1
This connector allows you to connect an ATX 24-pin power supply. To
connect the ATX 24-pin power supply, make sure the plug of the power
supply is inserted in the proper orientation and the pins are aligned.
Then push down the power supply firmly into the connector. You may
use the 20-pin ATX power supply as you like. If you
’
d like to use the
20-pin ATX power supply, please plug your power supply along with pin
1 & pin 13. There is also a foolproof design on pin 11, 12, 23 & 24 to
avoid wrong installation.
ATX 12V Power Connector: JPW1
This 12V power connector is used to provide power to the CPU.
Floppy Disk Drive Connector: FDD1
The mainboard provides a standard floppy disk drive connector that
supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types.
IDE Connector: IDE1/ IDE2
The mainboard has dual Ultra DMA 33/66/100/133 controller that provides PIO mode 0~4,
Bus Master, and Ultra DMA 66/100 function. You can connect up to four hard disk drives,
CD-ROM, 120MB Floppy and other devices. The first hard drive should always be
connected to IDE1. IDE1 can connect a Master and a Slave drive. You must configure
second hard drive to Slave mode by setting the jumper accordingly.
MSI Reminds You...
If you install two hard disks on one cable, you must configure the second drive to Slave mode by
setting its jumper. Refer to the hard disk documentation supplied by hard disk vendors for jumper
setting instructions.
Serial ATA Connectors: SATA1/ SATA2
The mainboard provides dual high-speed Serial ATA interface ports. These ports support
1
st
generation Serial ATA data rates of 150MB/s and are fully compliant with Serial ATA
1.0 specifications. Each Serial ATA connector can connect to 1 hard disk device.
MSI Reminds You...
Please do not fold the serial ATA cable in a 90-degree angle, which will cause the loss of data
during transmission.
CD-In Connector: CD_IN1
The connector is for CD-ROM audio connector.
1
12
24
13
+3.3V
+3.3V
-12V
+3.3V
GND
GND
PS-ON#
+5V
GND
GND
GND
+5V
GND
GND
Res
PWR OK
+5V
5VSB
+5V
+12V
+5V
+12V
GND
NC
1
3
4
2
GND
12V
GND
12V
1
7
L
R
GND