Magnavox 32MF330B User manual, English (US) - Page 10

Preparation

Page 10 highlights

PREPARATION No supplied cables are used with these connections: Please purchase the necessary cables at your local store. High Speed HDMI cable (also known as HDMI category 2 cable) is recommended for the better compatibility. Before you connect: Be sure your antenna or other device is connected properly before plugging in the AC power cord. Antenna Connection Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit. e.g.) 32MF330B Connection to Cable Receiver or Satellite Box Use an HDMI or component video cables to connect the HDMI or the Component Video Input jacks of the unit to the HDMI or the component video output jacks of the cable receiver / satellite box. If you connect to the unit's Component Video Input jacks, connect audio cables to the Audio L/R Input jacks right beside the Component Video connector. e.g.) 32MF330B satellite dish or cable TV signal including PPV RF coaxial cable ANT IN cable receiver / satellite box STEREO PCM HDMI OUT or AUDIO OUT L R COMPONENT VIDEO OUT Y Pb/Cb Pr/Cr VHF / UHF analog or DTV antenna rear of this unit RF coaxial cable HDMI cable (green) (blue) (red) component video cables (red/blue/green) and audio cables or or cable TV signal 26MF330B RF coaxial cable rear of this unit Once connections are completed, turn on the unit and begin initial setup. Channel scanning is necessary for the unit to memorize all available channels in your area. [Initial Setup] ➠ p.15 Note • If you have any question about the DTV's antenna, visit www.antennaweb. org for further information. • Depending on your antenna system, you may need different types of combiners (mixers) or separators (splitters). Contact your local electronics store for these items. • For your safety and to avoid damage to this unit, please unplug the RF coaxial cable from the antenna input jack before moving the unit. • If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be more effective than a set top or inside antenna. • To switch your reception source easily between antenna and cable, install an antenna selector. • If you are not receiving a signal from your cable service, contact the Cable provider. 10 EN or side or rear of this unit

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37

10
EN
PREPARATION
No supplied cables are used with these connections:
Please purchase the necessary cables at your local store.
High Speed HDMI cable (also known as HDMI category 2
cable) is recommended for the better compatibility.
Before you connect:
Be sure your antenna or other device is connected properly
before plugging in the AC power cord.
Antenna Connection
Connect the RF coaxial cable on your home outlet to the
antenna input jack of this unit.
e.g.)
e.g.)
VHF / UHF
analog
or
DTV antenna
cable TV signal
rear of this unit
rear of this unit
or
RF coaxial cable
RF coaxial cable
32MF330B
26MF330B
Once connections are completed, turn on the unit and begin initial
setup. Channel scanning is necessary for the unit to memorize all
available channels in your area.
[Initial Setup]
p.15
Note
If you have any question about the DTV’s antenna, visit www.antennaweb.
org for further information.
Depending on your antenna system, you may need different types of
combiners (mixers) or separators (splitters). Contact your local electronics
store for these items.
For your safety and to avoid damage to this unit, please unplug the RF
coaxial cable from the antenna input jack before moving the unit.
If you use an antenna to receive analog TV, it should also work for DTV
reception. Outdoor or attic antennas will be more effective than a set top
or inside antenna.
To switch your reception source easily between antenna and cable, install an
antenna selector.
If you are not receiving a signal from your cable service, contact the Cable
provider.
Connection to Cable Receiver or
Satellite Box
Use an HDMI or component video cables to connect the
HDMI or the Component Video Input jacks of the unit to
the HDMI or the component video output jacks of the cable
receiver / satellite box.
If you connect to the unit’s Component Video Input jacks,
connect audio cables to the Audio L/R Input jacks right beside
the Component Video connector.
e.g.)
32MF330B
STEREO
PCM
HDMI OUT
ANT IN
COMPONENT VIDEO OUT
Pr/Cr
Pb/Cb
Y
AUDIO OUT
R
L
satellite dish
cable receiver /
satellite box
cable TV signal
including PPV
RF coaxial cable
or
or
or
or
HDMI cable
side or rear of
this unit
component video cables
mponent video
o
m
component video cables
reen)
(red/blue/green)
(red/blue/g
(
)
(red/blue/green)
nd audio cab
b
and audio cables
b
b
d
d
bl
and audio cables
red
(
(
d)
d
red
d
(
d)
(red)
(
b
b e)
b
b
(bl
)
(blue)
ree
ree
(green)
ree
(green)
(green)