Makita GA5093 Instruction Manual - Page 11

Installing abrasive cut-off / diamond, wheel, Installing wire cup brush

Get Makita GA5093 PDF manuals and user guides View all Makita GA5093 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Installing abrasive cut-off / diamond wheel Optional accessory WARNING: When using an abrasive cut-off / diamond wheel, be sure to use only the special wheel guard designed for use with cut-off wheels. WARNING: NEVER use cut-off wheel for side grinding. 1 2 3 4 Fig.14 ► 1 . Lock nut 2. Abrasive cut-off wheel / diamond wheel 3. Inner flange 4. Wheel guard for abrasive cut-off wheel / diamond wheel As for the installation, follow the instructions for depressed center wheel. The direction for mounting the lock nut and the inner flange varies by wheel type and thickness. Refer to the following figures. When installing the abrasive cut-off wheel: 11 23 When installing the diamond wheel: 11 23 44 Fig.16 ► 1 . Lock nut 2. Diamond wheel (Thinner than 4 mm (5/32″)) 3. Diamond wheel (4 mm (5/32″) or thicker) 4. Inner flange Installing wire cup brush Optional accessory CAUTION: Do not use brush that is damaged, or which is out of balance. Use of damaged brush could increase potential for injury from contact with broken brush wires. Place the tool upside down to allow easy access to the spindle. Remove any accessories on spindle. Thread wire cup brush onto spindle and tighten with supplied wrench. 1 44 Fig.17 ► 1 . Wire cup brush Fig.15 ► 1 . Lock nut 2. Abrasive cut-off wheel (Thinner than 4 mm (5/32")) 3. Abrasive cut-off wheel (4 mm (5/32") or thicker) 4. Inner flange 11 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
11
ENGLISH
Installing abrasive cut-off / diamond
wheel
Optional accessory
WARNING:
When using an abrasive cut-off
/ diamond wheel, be sure to use only the special
wheel guard designed for use with cut-off wheels.
WARNING:
NEVER use cut-off wheel for side
grinding.
1
3
2
4
Fig.14
►
1.
Lock nut
2.
Abrasive cut-off wheel / diamond
wheel
3.
Inner flange
4.
Wheel guard for abrasive
cut-off wheel / diamond wheel
As for the installation, follow the instructions for
depressed center wheel.
The direction for mounting the lock nut and the inner
flange varies by wheel type and thickness.
Refer to the following figures.
When installing the abrasive cut-off wheel:
1
1
4
4
2
3
Fig.15
►
1.
Lock nut
2.
Abrasive cut-off wheel (Thinner than 4
mm (5/32"))
3.
Abrasive cut-off wheel (4 mm (5/32")
or thicker)
4.
Inner flange
When installing the diamond wheel:
1
1
4
4
2
3
Fig.16
►
1.
Lock nut
2.
Diamond wheel (Thinner than 4 mm
(5/32″))
3.
Diamond wheel (4 mm (5/32″) or thicker)
4.
Inner flange
Installing wire cup brush
Optional accessory
CAUTION:
Do not use brush that is damaged,
or which is out of balance.
Use of damaged brush
could increase potential for injury from contact with
broken brush wires.
Place the tool upside down to allow easy access to the
spindle.
Remove any accessories on spindle. Thread wire cup
brush onto spindle and tighten with supplied wrench.
1
Fig.17
►
1.
Wire cup brush