Makita GA5093 Instruction Manual - Page 9

For depressed center wheel, flap disc, flex wheel, wire wheel brush / abrasive, cut-off wheel, diamond

Get Makita GA5093 PDF manuals and user guides View all Makita GA5093 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

For depressed center wheel, flap disc, flex wheel, wire wheel brush / abrasive cut-off wheel, diamond wheel 1. While pushing the lock lever, mount the wheel guard with the protrusions on the wheel guard aligned with the notches on the bearing box. NOTE: Push down the wheel guard straight. Otherwise, you cannot secure the wheel guard. 3. While pushing the lock lever toward A, rotate the wheel guard toward C, and then, change the angle of the wheel guard according to the work so that the operator can be protected. Align the lock lever with one of the holes in the wheel guard, and then release the lock lever to lock the wheel guard. C 1 3 A 2 C Fig.6 ► 1 . Lock lever 2. Notch 3. Protrusion 2. While pushing the lock lever toward A, hold down the portions B of the wheel guard as shown in the figure. B B A 1 2 Fig.8 ► 1 . Wheel guard 2. Hole To remove wheel guard, follow the installation procedure in reverse. Clip-on cutting wheel guard attachment Optional accessory NOTE: For cutting-off operations, a clip-on cutting wheel guard attachment can be used with the wheel guard (for grinding wheel). Not available in some countries. Fig.7 ► 1 . Wheel guard 2. Hole 1 2 Fig.9 9 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
9
ENGLISH
For depressed center wheel, flap disc,
flex wheel, wire wheel brush / abrasive
cut-off wheel, diamond wheel
1.
While pushing the lock lever, mount the wheel
guard with the protrusions on the wheel guard aligned
with the notches on the bearing box.
1
2
3
Fig.6
►
1.
Lock lever
2.
Notch
3.
Protrusion
2.
While pushing the lock lever toward A, hold down
the portions B of the wheel guard as shown in the figure.
2
B
1
A
B
Fig.7
►
1.
Wheel guard
2.
Hole
NOTE:
Push down the wheel guard straight.
Otherwise, you cannot secure the wheel guard.
3.
While pushing the lock lever toward A, rotate the
wheel guard toward C, and then, change the angle of
the wheel guard according to the work so that the oper-
ator can be protected. Align the lock lever with one of
the holes in the wheel guard, and then release the lock
lever to lock the wheel guard.
2
1
A
C
C
Fig.8
►
1.
Wheel guard
2.
Hole
To remove wheel guard, follow the installation proce-
dure in reverse.
Clip-on cutting wheel guard
attachment
Optional accessory
NOTE:
For cutting-off operations, a clip-on cutting
wheel guard attachment can be used with the wheel
guard (for grinding wheel).
Not available in some countries.
Fig.9