Makita XCM01Z Instruction Manual - Page 10

Operation lamp, Adjusting depth of cut

Get Makita XCM01Z PDF manuals and user guides View all Makita XCM01Z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Operation lamp CAUTION: Do not look in the light or see the source of light directly. To turn on the operation lamp, press and hold the lockoff button and pull the switch trigger. The lamp goes out approximately 15 seconds after releasing the switch trigger. Adjusting depth of cut CAUTION: After adjusting the depth of cut, always tighten the thumb screw securely. With the dust collection cover installed, fine adjustments in the cutting depth can be made up to 13.5 mm (1/2″). Loosen the thumb screw on the depth scale. Lift or lower the tool handle into position to align the depth indicators on the cover with your desired cutting depth on the scale. Then tightening the thumb screw. Fig.10 1 ► 1  . Operation lamp NOTICE: When the tool is operated with excessive load, the operation lamp flashes. In this situation, release the switch trigger, and then reduce the load on the tool before operating again. NOTICE: When the tool is overheated, the operation lamp flashes. In this case, release the switch trigger, and then cool down the tool/battery before operating again. NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. 1 3 2 Fig.11 ► 1  . Thumb screw 2. Depth scale 3. Depth indicator CAUTION: For clean and safe cutting, set the cutting depths so that a cutting wheel overpasses the undersurface of workpiece by 2.0 mm (1/16″) or less. Setting in proper cutting depths helps to reduce potential for dangerous kickbacks which may cause personal injury. 10 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
10
ENGLISH
Operation lamp
CAUTION:
Do not look in the light or see the
source of light directly.
To turn on the operation lamp, press and hold the lock-
off button and pull the switch trigger.
The lamp goes out approximately 15 seconds after
releasing the switch trigger.
1
Fig.10
►
1.
Operation lamp
NOTICE:
When the tool is operated with exces-
sive load, the operation lamp flashes. In this situ
-
ation, release the switch trigger, and then reduce
the load on the tool before operating again.
NOTICE:
When the tool is overheated, the opera-
tion lamp flashes. In this case, release the switch
trigger, and then cool down the tool/battery before
operating again.
NOTE:
Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Adjusting depth of cut
CAUTION:
After adjusting the depth of cut,
always tighten the thumb screw securely.
With the dust collection cover installed, fine adjustments
in the cutting depth can be made up to 13.5 mm (1/2″).
Loosen the thumb screw on the depth scale. Lift or
lower the tool handle into position to align the depth
indicators on the cover with your desired cutting depth
on the scale. Then tightening the thumb screw.
1
3
2
Fig.11
►
1.
Thumb screw
2.
Depth scale
3.
Depth indicator
CAUTION:
For clean and safe cutting, set the
cutting depths so that a cutting wheel overpasses
the undersurface of workpiece by 2.0 mm (1/16″) or
less. Setting in proper cutting depths helps to reduce
potential for dangerous kickbacks which may cause
personal injury.