Makita XTP02Z XTP02 Instruction Manual - Page 7

Assembly

Get Makita XTP02Z PDF manuals and user guides View all Makita XTP02Z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

1 A B ► 1 . Adjuster 1 2 3 ► 1 . Too deep 2. Flush 3. Too shallow Lighting up the lamp CAUTION: Do not look in the light or see the source of light directly. Pull the switch trigger or actuate the contact element to light up the lamp. The lamp keeps on lighting while pulling the switch trigger or actuating the contact element. The lamp goes out approximately 10 seconds after releasing the switch trigger and the contact element. ASSEMBLY CAUTION: Always make sure that your fingers are not placed on the switch trigger or the contact element and the battery cartridge is removed before carrying out any work on the pin nailer. Loading the pin nailer CAUTION: Always make sure that the battery cartridge is removed before loading the pin nailer. Unintentional firing may cause personal injuries and property damage. CAUTION: Do not abruptly slide the magazine of the pin nailer loaded with pin nails. Accidentally dropping pin nails especially when working in high places may cause personal injuries. CAUTION: Load pin nails in the correct direction. Loading in wrong direction may cause premature wear and tear of the driver and damage of the other parts. CAUTION: Do not use deformed connected pin nails. Use pin nails specified in this manual. Using pin nails other than those specified may cause pin nail jamming and breakage of the pin nailer. 1. Remove the battery cartridge. 2. Press the locking lever and slide the magazine backward. 3. Align the tip of pin nails with the grooves at the bottom of the magazine and push the whole part of pin nails toward the driver guide. (Be careful to place pin nails in the right direction.) 1 2 3 1 ► 1 . Lamp NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. NOTE: Even in the lamp lights up when the battery power residual gets small, pin nailer may not fire pin nails. In this case, charge the battery cartridge. 4 ► 1 . Pin nails 2. Magazine 3. Locking lever 4. Driver guide 7 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
7
ENGLISH
A
B
1
►
1.
Adjuster
2
1
3
►
1.
Too deep
2.
Flush
3.
Too shallow
Lighting up the lamp
CAUTION:
Do not look in the light or see the
source of light directly.
Pull the switch trigger or actuate the contact element to
light up the lamp. The lamp keeps on lighting while pull-
ing the switch trigger or actuating the contact element.
The lamp goes out approximately 10 seconds after
releasing the switch trigger and the contact element.
1
►
1.
Lamp
NOTE:
Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
NOTE:
Even in the lamp lights up when the battery
power residual gets small, pin nailer may not fire pin
nails. In this case, charge the battery cartridge.
ASSEMBLY
CAUTION:
Always make sure that your fingers
are not placed on the switch trigger or the contact
element and the battery cartridge is removed
before carrying out any work on the pin nailer.
Loading the pin nailer
CAUTION:
Always make sure that the battery
cartridge is removed before loading the pin nailer.
Unintentional firing may cause personal injuries and
property damage.
CAUTION:
Do not abruptly slide the magazine
of the pin nailer loaded with pin nails.
Accidentally
dropping pin nails especially when working in high
places may cause personal injuries.
CAUTION:
Load pin nails in the correct direc-
tion.
Loading in wrong direction may cause premature
wear and tear of the driver and damage of the other parts.
CAUTION:
Do not use deformed connected
pin nails.
Use pin nails specified in this manual.
Using pin nails other than those specified may cause
pin nail jamming and breakage of the pin nailer.
1.
Remove the battery cartridge.
2.
Press the locking lever and slide the magazine
backward.
3.
Align the tip of pin nails with the grooves at the
bottom of the magazine and push the whole part of pin
nails toward the driver guide. (Be careful to place pin
nails in the right direction.)
3
2
4
1
►
1.
Pin nails
2.
Magazine
3.
Locking lever
4.
Driver
guide