Marantz NR1402 NR1402N_ENG_CD-ROM_v00 - Page 52

Surr.Parameter, HT-EQ, ENTER

Get Marantz NR1402 PDF manuals and user guides View all Marantz NR1402 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Basic version Advanced version Surr.Parameter Default settings are underlined. Adjust surround sound parameters. It may not be possible to set this item depending on the input signal (vpage 80 "Surround modes and surround parameters"). Setting items HT-EQ Soften the treble range of movie soundtracks for better understanding. Setting details ON : "HT-EQ" is used. OFF : "HT-EQ" is not used. This can also be set by pressing HT-EQ. DRC Compress dynamic range (difference between loud and soft sounds). D.Comp Compress dynamic range (difference between loud and soft sounds). LFE Adjust the low-frequency effects level (LFE). C.Image Assign center channel signal to front left and right channels for wider sound. Panorama Assign front L/R signal also to surround channels for wider sound. Dimension Shift sound image center to front or rear to adjust playback balance. Auto : Automatic dynamic range compression on/off control according to source. This can be set in the Dolby TrueHD mode. Low / Middle / High : These set the compression level. OFF : Dynamic range compression always off. OFF : Turn dynamic range compression off. Low / Middle / High : These set the compression level. -10dB - 0dB For proper playback of the different sources, we recommend setting to the values below. • Dolby Digital sources : "0dB" • DTS movie sources : "0dB" • DTS music sources : "-10dB" 0.0 - 1.0 (0.3) ON : Set. OFF : Do not set. 0 - 6 (3) Audio Adjust Setting items Setting details C.Width 0 - 7 (3) Assign center channel signal to front left and right channels for wider sound. Height Gain Control the front channel volume. Low : Reduce the front height channel volume. height Middle : Front height channel sound is output with standard sound volume. High : Increase the front height channel volume. Default The "Surr.Parameter" settings are returned to the default settings. NOTE "Height Gain" is displayed for the following settings. • When "Pre Assign" (vpage 55) is set to "F.HEIGHT". • When the "Speaker Config." - "F.Height" setting (vpage 56) is set other than to "None". • When surround mode is "PLgz" or the PLgz decoder is used. Yes : Reset to the defaults. No : Do not reset to the defaults. When you select "Default" and press ENTER, the "Return settings to the default?" prompt is displayed. Select either "Yes" or "No", and press ENTER. vSee overleaf Information BD 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
49
Surr.Parameter
Default settings are underlined.
Adjust surround sound parameters. It may not be possible to set this item depending on the input signal
(
v
page 80
“Surround modes and surround parameters”).
Setting items
Setting details
HT-EQ
Soften the treble range
of movie soundtracks for
better understanding.
ON
: “HT-EQ” is used.
OFF
: “HT-EQ” is not used.
This can also be set by pressing
HT-EQ
.
DRC
Compress dynamic range
(difference between loud
and soft sounds).
Auto
: Automatic dynamic range compression on/off control according to
source. This can be set in the Dolby TrueHD mode.
Low
/
Middle
/
High
: These set the compression level.
OFF
: Dynamic range compression always off.
D.Comp
Compress dynamic range
(difference between loud
and soft sounds).
OFF
: Turn dynamic range compression off.
Low
/
Middle
/
High
: These set the compression level.
LFE
Adjust the low-frequency
effects level (LFE).
–10dB – 0dB
For proper playback of the different sources, we recommend setting
to the values below.
•
Dolby Digital sources : “0dB”
•
DTS movie sources : “0dB”
•
DTS music sources : “–10dB”
C.Image
Assign center channel
signal to front left and right
channels for wider sound.
0.0 – 1.0 (0.3)
Panorama
Assign front L/R signal also
to surround channels for
wider sound.
ON
: Set.
OFF
: Do not set.
Dimension
Shift sound image center
to front or rear to adjust
playback balance.
0 – 6 (3)
Audio Adjust
Setting items
Setting details
C.Width
Assign center channel
signal to front left and right
channels for wider sound.
0 – 7 (3)
Height Gain
Control
the
front
height
channel volume.
Low
: Reduce the front height channel volume.
Middle
: Front height channel sound is output with standard sound
volume.
High
: Increase the front height channel volume.
NOTE
“Height Gain” is displayed for the following settings.
•
When “Pre Assign” (
v
page 55
) is set to “F.HEIGHT”.
•
When the “Speaker Config.” – “F.Height” setting (
v
page 56
) is set
other than to “None”.
•
When surround mode is “PL
g
z” or the PL
g
z decoder is used.
Default
The “Surr.Parameter”
settings are returned to the
default settings.
Yes
: Reset to the defaults.
No
: Do not reset to the defaults.
When you select “Default” and press
ENTER
,
the “Return settings to the default?” prompt
is displayed. Select either “Yes” or “No”, and
press
ENTER
.