Marantz NR1402 NR1402N_ENG_CD-ROM_v00 - Page 72

Registering preset codes, Buttons used for operating the devices, Entering a 4-digit code

Get Marantz NR1402 PDF manuals and user guides View all Marantz NR1402 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Basic version Advanced version Registering preset codes When preset codes are registered in the included remote control unit, it can then be used to operate any devices you have, such as DVD players or TVs made by different manufacturers. NOTE • No preset codes other than BD, DVD, SAT, TV and CD can be registered. • In the factory settings, remote control codes for all marantz products are registered. nnButtons used for operating the devices q SOURCE Z / X For switching power of each device on or off. w uio p, ENTER For menu operation of each device. e MENU, SHIFT/TOP MENU For displaying the menu of each device. r 3, 1, 2, 8, 9, 6, 7 t Number button (0 - 9, +10) y PRESET +, PRESET - u TV Z / X, TV INPUT For operating a TV This button is enabled in any mode. For details on operation with the remote control unit, see pages 23, 71, 72. Registering preset codes The following two methods can be used for registering the reset code. q Entering a 4-digit code w Scanning the code table q Entering a 4-digit code See the preset code list table for the code to be input. 1 Press and hold down the input source select buttons for the appliance to control, and press SET until the SET indicator blinks. 2 Press the 4-digit code for the appliance using 0 - 9 (code table at the end of this book). When the procedure is successful, the SEND indicator blinks twice. NOTE If the SEND indicator did not blink twice, then repeat steps 1 and 2 and try entering the same code again. w Scanning the code table 1 Switch the power of the appliance to which you want to register the preset code to ON. 2 Press and hold down the input source select buttons for the appliance to control, and press SET until the SET indicator blinks. 3 Aim the remote control at the appliance and slowly alternate between pressing SOURCE d and SOURCE Z /X for the appliance. 4 When the power of the appliance that you want to register has turned off, release the button. 5 Press ENTER. When the procedure is successful, the SEND indicator blinks twice. vSee overleaf Information 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
69
Registering preset codes
When preset codes are registered in the included remote control unit,
it can then be used to operate any devices you have, such as DVD
players or TVs made by different manufacturers.
NOTE
•
No preset codes other than
BD
,
DVD
,
SAT
,
TV
and
CD
can be
registered.
•
In the factory settings, remote control codes for all marantz products
are registered.
n
Buttons used for operating the devices
q
SOURCE
Z
/
X
For switching power of each device on or off.
w
uio
p
,
ENTER
For menu operation of each device.
e
MENU
,
SHIFT/TOP
MENU
For displaying the menu of each device.
r
3
,
1
,
2
,
8
,
9
,
6
,
7
t
Number button (
0
–
9
,
+10
)
y
PRESET +
,
PRESET –
u
TV
Z
/
X
,
TV INPUT
For operating a TV
This button is enabled in any mode.
For details on operation with the remote control unit, see pages
23
, 
71
, 
72
.
Registering preset codes
The following two methods can be used for registering the reset code.
q
Entering a 4-digit code
w
Scanning the code table
q
Entering a 4-digit code
See the preset code list table for the code to be input.
1
Press and hold down the input
source select buttons for the
appliance to control, and press
SET
until the SET indicator
blinks.
2
Press the 4-digit code for the
appliance using
0
-
9
(code table
at the end of this book).
When the procedure is successful, the
SEND indicator blinks twice.
NOTE
If the SEND indicator did not blink twice,
then repeat steps 1 and 2 and try entering
the same code again.
w
Scanning the code table
1
Switch the power of the appliance
to which you want to register the
preset code to ON.
2
Press and hold down the input
source select buttons for the
appliance to control, and press
SET
until the SET indicator
blinks.
3
Aim the remote control at the
appliance and slowly alternate
between pressing
SOURCE
d
and
SOURCE
Z
/
X
for the appliance.
4
When the power of the appliance
that you want to register has
turned off, release the button.
5
Press
ENTER
.
When the procedure is successful, the
SEND indicator blinks twice.