Marantz SA8260 SA8260 User Guide - Page 22

Trouble Shooting - problems

Get Marantz SA8260 PDF manuals and user guides View all Marantz SA8260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

ENGLISH TROUBLE SHOOTING If you think a malfunction has occurred, first check the points listed below, The problem is likely to have been caused by a simple operational error or a connection problem. If the problem cannot be corrected even after carrying out the following checks, consult your dealer or nearest Marantz sales office or service counter. • The disc fails to rotate. 1. Is the mains lead plugged in properly? 2. Is the POWER switch ON? 3. Is the disc placed in the correct position on the disc tray? 4. Is the disc placed properly with the label side facing up? 5. Is the disc dirty? 6. Is the disc scratched? 7. Is the disc warped? • The disc is rotating but no sound is heard. 1. Are the amplifier and speakers connected properly? 2. Is the amplifier switch ON? 3. Is the amplifier's volume control set at the minimum level? 4. Is the amplifier's selector switch set to the correct input ("CD" or "AUX", whichever corresponds to the input jacks the SACD player is connected to)? • The disc stops in mid-operation. The sound drops out or noise is heard. 1. Is the disc dirty? 2. Is the disc scratched? 3. Is the disc warped? * In the case of a CD-R or CD-RW disc, this problem may occur when the conditions under which its data was originally written were substandard or when the quality of the disc itself is poor. • Remote control operation is not possible. 1. Is the remote control unit's transmitter pointed correctly at the remote sensor on the front of the SACD player? Or is there an obstruction between the transmitter and the remote sensor? 2. Are the batteries in the remote control unit exhausted? 3. Is there another strong light (from a window, etc.) striking the SACD player's remote sensor? • A Super Audio CD cannot be played. 1. Is the disc scratched, dirty or warped? 2. Is the amplifier's input selector set to digital? * Digital audio signal will not be output when a Super Audio CD is played. • Some channels are not played (Super Audio CD MultiChannel) 1. Confirm the number of channels in the disc. (See page 11) • A CD-R/CD-RW disc cannot be played. 1. Is the disc placed upside down? 2. Is the disc contains properly written TOC? 3. Is the recorded information in an audio (CD-DA) format? 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
ENGLISH
17
If you think a malfunction has occurred, first check the points
listed below, The problem is likely to have been caused by a
simple operational error or a connection problem. If the
problem cannot be corrected even after carrying out the
following checks, consult your dealer or nearest Marantz sales
office or service counter.
•
The disc fails to rotate.
1.
Is the mains lead plugged in properly?
2.
Is the POWER switch ON?
3.
Is the disc placed in the correct position on the disc tray?
4.
Is the disc placed properly with the label side facing up?
5.
Is the disc dirty?
6.
Is the disc scratched?
7.
Is the disc warped?
•
The disc is rotating but no sound is heard.
1.
Are the amplifier and speakers connected properly?
2.
Is the amplifier switch ON?
3.
Is the amplifier’s volume control set at the minimum level?
4.
Is the amplifier’s selector switch set to the correct input
(“CD” or “AUX”, whichever corresponds to the input jacks
the SACD player is connected to)?
•
The disc stops in mid-operation.
The sound drops out or noise is heard.
1.
Is the disc dirty?
2.
Is the disc scratched?
3.
Is the disc warped?
* In the case of a CD-R or CD-RW disc, this problem may
occur when the conditions under which its data was
originally written were substandard or when the quality of
the disc itself is poor.
•
Remote control operation is not possible.
1.
Is the remote control unit’s transmitter pointed correctly at
the remote sensor on the front of the SACD player?
Or is there an obstruction between the transmitter and the
remote sensor?
2.
Are the batteries in the remote control unit exhausted?
3.
Is there another strong light (from a window, etc.) striking
the SACD player’s remote sensor?
•
A Super Audio CD cannot be played.
1.
Is the disc scratched, dirty or warped?
2.
Is the amplifier’s input selector set to digital?
* Digital audio signal will not be output when a Super Audio
CD is played.
TROUBLE SHOOTING
•
Some channels are not played (Super Audio CD Multi-
Channel)
1.
Confirm the number of channels in the disc. (See page
11)
•
A CD-R/CD-RW disc cannot be played.
1.
Is the disc placed upside down?
2.
Is the disc contains properly written TOC?
3.
Is the recorded information in an audio (CD-DA) format?