Marantz SR7001 User Manual - Page 53

ENGLISH PRESET MEMORY With this unit you can preset up to 60 FM/AM stations in any order. For each station, you can memorize the frequency and reception mode if desired. AUTO PRESET MEMORY This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory. 2. 4. 1. 3. 2. 5. AV SURROUND RECEIVER SR8001 INPUT SELECTOR PURE DIRECT DSD DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST SPKR A B V-OFF PEAK ATT DISC 6.1 MTX 6.1 NIGHT EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR STANDBY POWER ON/STANDBY PHONES SURROUND MODE AUTO MULTI MULTI SPEAKER BAND T-MODE MEMORY CLEAR PURE DIRECT THX 7.1CH INPUT MENU ENTER DISPLAY EXIT MultEQ SPEAKERS A/B MIC VOLUME READY DOWN UP DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R 1. To select FM , press the BAND button on the front panel. 2. While pressing the MEMORY button, press the 1 cursor button. "AUTO PRESET" will appear on the display, and scanning starts from the lowest frequency. 3. Each time the tuner finds a station, scanning will pause and the station will be played for five seconds. During this time, the following operations are possible. The band can be changed by the BAND button. 4. If no button is pressed during this period, the current station is memorized in location Preset 02. If you wish to skip the current station, press the 3 cursor button during this period, this station is skipped and auto presetting continues. 5. Operation stops automatically when all 50 preset memory positions are filled or when auto scanning attains the highest end of all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button. MANUAL PRESET MEMORY 3. 2. 4. DIRECT SD DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST SPKR A B V-OFF PEAK ATT DISC 6.1 MTX 6.1 NIGHT EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR SURROUND MODE AUTO MULTI MULTI SPEAKER BAND T-MODE MEMORY CLEAR PURE DIRECT THX 7.1CH INPUT MENU ENTER DISPLAY EXIT MultEQ SPEAKERS A/B MIC DO DIG PREV MENU TEST 1 7.1CH 4 DISP 7 CLEAR LIP.SYNC GUIDE CH.SEL 2 ATT 5 OSD 8 THX 0 MUTE EXIT SURR 3 SPK-AB 6 SLEEP 9 MEMO 3. 2. (Using the SR7001) 1. Tune into the radio station you desire (Refer to the "MANUAL TUNING" or "AUTO TUNING" section). 2. Press the MEMORY button on the front panel. "- -" (preset number) starts blinking on the display. 3. Select the preset number by pressing the 1 or 2 cursor buttons, while this is still blinking (approx. 5 seconds) 4. Press the MEMORY button again to enter. The display stops blinking. The station is now stored in the specified preset memory location. (Using the remote control unit) 1. Tune into the radio station you desire (Refer to the "MANUAL TUNING" or "AUTO TUNING" section). 2. Press the MEMO button on the remote. "- -" (preset number) starts blinking on the display. 3. Enter the desired preset number by pressing the numeric buttons. Note: • When entering a single digit number (2 for example), either input "02" or just input "2" and wait for a few seconds. RECALLING A PRESET STATION TV DVD VCR DSS TUNER CD CD-R MD TAPE 1 AUX1 AUX2 LIGHT RC8001SR Learning Remote Controller AMP 2 1. 2. (Using the SR7001) CH VOL OK PREV LIP.SYNC GUIDE MUTE 1. Select the desired preset station by pressing the 1 or 2 cursor buttons on the front panel. (Using the remote control unit) 1. Press the TUNER button twice within two seconds on the remote. 2. Press the > button until PAGE4 is displayed 3. Press the P-SET+ (D4) or P-SET- (D5) button to tune in the deseired preset station. Or enter the preset station number with the numeric buttons. PRESET SCAN USE PAGE 2 M D1 D2 D3 D4 D5 TUNER CD CD-R MD TAPE 1 AUX1 AUX2 LIGHT RC8001SR Learning Remote Controller AMP 2 2. 4. 5. 2. CH VOL OK PREV MENU TEST 1 LIP.SYNC GUIDE CH.SEL 2 MUTE EXIT SURR 3 1. 4 DISP 7 CLEAR 5 OSD 8 THX 0 6 SLEEP 9 MEMO 5. (Using the remote control unit) 1. Press the TUNER button twice within two seconds on the remote. 2. Press the > button until PAGE2 is displayed and press the P-SCAN (D4) on the remote. "PRESET SCAN" appears on the front display and then the preset station with the lowest preset number is recalled first. 3. Preset stations are recalled in sequence (No.1 → No.2 → etc.) for 5 seconds each. No stored preset number will be skipped. 4. You can fast forward the preset stations, press the > button until PAGE4 is displayed and press the P-SET+ (D4) continuously. 5. When the desired preset station is received, cancel the preset scan operation by pressing the CLEAR button or P-SCAN (D4) on the remote. 50