Marantz SR9200 User Guide - Page 13
Rear Panel - model
View all Marantz SR9200 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 13 highlights
ENGLISH REAR PANEL z x cv b n m ,. ⁄0 DIGITAL-OUT OPT COAX RS232C EXT. IR OUT DC OUT 1 DC OUT 2 IN MULTI RC OUT RC-5 PRE OUT MAIN IN 1L GND ANTENNA 2 R 3 C GND AM 4 SW 5 SL R FRONT L CD 6 SR 7 SBL SURR. SURR. BACK IN TAPE OUT 8 SBR 9 MULTI OUT DIGITAL-IN R L IN S.W CD-R CENTER /MD OUT 7.1CH-IN R AUDIO L MULTI VIDEO OUT R L MONI. 2 MONI. 1 LD MODEL NO.SR9200 Y CB MONITOR OUT - + FRONT LEFT FRONT RIGHT - + MULTI ROOM LEFT MULTI ROOM RIGHT DVD DSS TV CR Y DSS IN CB VCR2/ DVD-R IN SURR. BACK LEFT SURR. BACK RIGHT CENTER SURR. LEFT IN VCR1 OUT IN VCR2/ DVD-R OUT CR Y DVD IN CB CR VCR1 IN VIDEO S-VIDEO COMPONENT VIDEO SWITCHED 120W 1A SURR. RIGHT SPEAKER SYSTEMS 6-8 OHMS UNSWITCHED 120W 1A AC OUTLETS 120V 60HZ AC IN ¤0 ⁄9 ⁄8 ⁄7 ⁄6 ⁄5 ⁄4 ⁄3 ⁄2 ⁄1 z DIGITAL INPUT (Dig.1 - 9) / OUTPUT (coaxial, optical) These are the digital audio inputs and outputs. There are 5 digital inputs with coaxial jacks, 4 with optical jacks. The inputs accept digital audio signals from a compact disc, LD, DVD, or other digital source component. For digital output, there is 1 coaxial output and 1 optical output. The digital outputs can be connected to MD recorders, CD recorders, DAT decks, or other similar components. x Preamp Outputs (L, R, SL, SR, SBL, SBR, C) When the jumper plugs that link the Amplifier Inputs with these outputs are removed, these jacks may be connected to an external power amplifier. c Subwoofer Output Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a "Y" connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier. v Main Amplifier Inputs When the jumper plugs that link the Preamp Outputs with these inputs are removed, these jacks may be used to connect an external source to the internal amplifiers. Notes: • When connecting a equipment, remove the attached jumper plugs and store them carefully so as not to lose them. • Only remove the jumper plugs when required. After you finish using an Main Amp Input jack, replace the jumper plug. b FM antenna terminal (75 ohms) Connect an external FM antenna with a coaxial cable, or a cable network FM source. AM antenna and ground terminals Connect the supplied AM loop antenna. Use the terminals marked "AM" and "GND". The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best n Multiroom Outputs (Audio L&R, Video) These are the audio and video output jacks for the remote zone (Multi Room). Connect these jacks to the optional audio power amplifiers or video display devices to view and listen to the source selected by the mulitroom system in a remote room. m MONITOR OUT There are 2 monitor outputs and each one includes both composite video and S-video configurations. When connecting two video monitors or televisions, be aware that the OSD interface can be used with both MONITOR OUT. 9